4-羟基-3-碘-5-硝基苯甲腈的新合成方法

报道了以对羟基苯甲醛为原料，经过硝化、腈化和碘化反应合成牛羊抗肝片吸虫药4-羟基-3-碘-5-硝基苯甲腈的新方法，总收率为76．9％，纯度达96．8％。     

炭黑－环氧树脂导电复合材料的研究

本文研究了炭黑－环氧树脂复合材料的制备工艺及炭黑填充率对材料电阻率的影响。实验结果表明，加入表面活性剂，明显改善了炭黑在环氧树脂中分布的均匀性。炭黑－环氧树脂材料具有明显的渗流效应，正温度系数效应即ＰＴＣ效应，非线性伏安特性和电磁波屏蔽效应。     

Ion‐exchange resins. II. Acrylamide crosslinked copolymers as precursors for some ion exchangers

Crosslinked copolymers of acrylamide (AA) and ethylacrylate and some ion exchangers derived from them containing either primary amine groups, obtained by the Hofmann degradation of the amide groups, or carboxylic groups, obtained by the alkaline hydrolysis of the ester groups, were studied. Divinylbenzene and N,N′‐methylenebisacrylamide were used as crosslinkers. The starting copolymers and the corresponding ion exchangers were characterized by IR spectroscopy, swelling behavior, and thermogravimetric analysis. The ion‐exchanger properties were correlated with the crosslinker nature and the chemical reactions performed on the AA copolymers. The average molecular weight between two crosslinks, determined from the swelling data in water, was compared with that calculated on the basis of the copolymerization stoichiometry only for the carboxylic cation exchangers. In this way, the preservation of the crosslink density after the hydrolysis was revealed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2701–2707, 2003     

过磷酸钙含氟尾气处理的新方法

对动态泡沫床处理过磷酸钙含氟尾气的有关技术及费用作了说明 ,指出该方法费用高 ;提出一种新方法 ,该方法不加任何化学助剂 ,采用水作吸收剂 ,只需改变动态泡沫床一些设计参数和选用一种特殊的喷头 (喷头周围设计 1个圆锥形死角区 ,使含氟气体不可能进入该区 )避免了硅胶堵塞。该方法已在湖南浦市化工总厂运行 1年多未发现堵塞 ,同时该法投资少、能耗低、排放尾气达标     

Surface hydrolysis of filaments based on poly(trimethylene terephthalate) spun at high spinning speeds

The surface alkaline hydrolysis of fibers made from poly(trimethylene terephthalate) (PTT) was studied after extruding the polymer at high spinning speeds from 2000 to 6000 m/min and heat setting in the range of temperatures from 100 to 180°C. Fiber weight loss increased with an increasing heat‐setting temperature but it was also dependent on the spinning speed. Some of the partially hydrolyzed fibers had a well‐developed, hydrophilic surface, and pore size in the range of 0.69 to 1.20 μm. The optimum reaction and morphological conditions for increasing porosity in PTT fibers depends on spinning speed and heat‐setting temperature. A temperature of 180°C is the upper limit for heat‐setting PTT filaments but seems to be the most effective for making porous fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1724–1730, 2004     

R-卡尼丁的合成和改进

以环氧氯丙烷为原料合成了 ( R,S) -卡尼丁 ,用二苯甲酰 - L-酒石酸对其进行了拆分 ,对反应和拆分条件进行了优化 ,并用氧化还原法实现了 S-卡尼丁的消旋化 ,使其可以回收利用。     

User experience and personal innovativeness: An empirical study on the Enterprise Resource Planning systems

Although user experience and personal innovativeness are two important factors in new technology adoption, there has been no prior study to test these factors with the Enterprise Resource Planning (ERP) adoption. This paper investigates moderating roles of user experience on the relationship between the personal innovativeness and the ERP adoption motivations. This issue is important because if the user has more experience with the systems then the power of influence of personal innovativeness on ERP adoption motivation would be different. Thus, this paper tests these important insights of ERP systems adoption with the two different field samples with high (more than three years) and low (less than three years) user experience, based on the innovation diffusion theory, self determination theory, and different types of motivations such as intrinsic and extrinsic motivations. The findings, based on the PLS analysis of the model using 107 ERP end users, show that there are clear moderating effects of user experience—such as impacts of personal innovativeness on ERP systems adoption motivations are higher in case of low user experience samples, as expected. Academic and practical implications are discussed in the paper based on these empirical findings.     

甲烷浓度对金刚石薄膜(100)织构生长的影响

以H2和CH4的混合气体为气源,用微波等离子体辅助化学气相沉积法(MPECVD)在1 cm×1 cm S i(100)基体上沉积了金刚石薄膜。研究了不同的甲烷浓度对金刚石薄膜(100)织构生长趋势的影响。分别采用扫描电子显微镜(SEM),Ram an光谱对金刚石膜的表面形貌、质量进行了分析。结果表明,当基体温度为750℃,气压为4.8×103Pa,甲烷浓度为1.4%时,薄膜表面为(100)织构。     

Hydrogen evolution during the oxidation of formaldehyde on Au:: The influence of single crystal structure and Tl-upd

Hydrogen evolution during formaldehyde oxidation in alkaline solution has been monitored by Differential Electrochemical Mass Spectrometry on Au(111) and polycrystalline gold. The current efficiency for hydrogen evolution increases with higher concentration and is in the same range on both, polycrystalline Au and Au(111) electrode. The onset potentials and half-wave potentials are higher on Au(111). Reaction orders for the faradaic current on the bare gold electrodes have been determined as 0.21 for higher and 0.76 for lower concentrations. Reaction orders for hydrogen evolution during formaldehyde oxidation are 1.4 times higher in each case. Tafel slopes in the range of 140-160 mV are found. This signifies that the first reaction step involving the formation of adsorbed hydrogen is largely determining the overall reaction rate. In the presence of thallium adlayers hydrogen evolution from formaldehyde oxidation is largely suppressed. On the thallium modified polycrystalline Au, formaldehyde oxidation is shifted for 100 mV to higher potentials where Tl is partially desorbed and hydroxide is coadsorbed on the modified surface. On thallium modified Au(111), a similar process takes place, but in the same potential region as the onset of formaldehyde oxidation on the bare surface and therefore the formaldehyde oxidation is only slightly shifted. Tafel slopes are decreased to 80 mV/dec in the presence of thallium. In the presence of adsorbed thallium, the first reaction step is in equilibrium, the coverage with adsorbed hydrogen is smaller and its recombination to H₂ is largely suppressed.