浅谈循环流化床锅炉技术的发展与应用

介绍循环流化床锅炉发展概况 ,基本原理、应用及优缺点     

热力系统节能技术改造方案介绍

针对热电厂热力系统存在的浪费能源和设计不合理现象作了浅析 ,介绍了几种对热力系统进行改造的方案 ,并对取得的经济效益进行了计算。     

Off-Optimum Cure of Aerospace Epoxy Adhesives

Four epoxy film adhesives used in aircraft manufacture and repair have been examined to establish the effect of deviation from the cure cycle specified by the manufacturer. In addition to the variation of the cure cycle, two surface preparations of the aluminium adherends (chromic acid etch or grit blast followed by silane treatment) were evaluated. Thermal analysis was used to examine the cure envelope of the adhesive, and its extent of cure and glass transition temperature. The adhesive properties were assessed by shear strength (in both single lap joints and in Iosipescu configuration), durability (Boeing wedge test) and chemical resistance to selected aggressive fluids. The sensitivity of the performance of a particular adhesive to offoptimum cure conditions depends on its composition and needs to be determined, not predicted.     

碳纤维表面处理对铝电解用硼化钛阴极涂层性能的影响

硼化钛阴极涂层是铝电解用可润湿性阴极材料中的一种，具有优良的抗钠渗透性和对铝液润湿性，可以有效地延长铝电解槽寿命。碳纤维是硼化钛涂层材料的增强剂之一．对硼化钛阴极涂层的性能影响很大。本文研究了不同工艺的液相碳纤维表面氧化处理法对硼化钛阴极涂层抗拉强度和粘接强度的影响。采用PTIR检测碳纤维处理后表面含氧基团的变化，寻找影响硼化钛阴极涂层性能的原因，从而达到最有效地提高TiB2阴极涂层抗拉强度和粘接强度的目的。结果表明，采用工艺(1)(10％HNO3，80℃、恒温5min．超声波、5min)对碳纤维进行表面处理最合理，处理后碳纤维表面含氧基团的含量最高．用其制备硼化钛阴极涂层的抗拉强度、粘接强度最大。     

PTS瞬态流动与换热数值模拟研究

为了研究压水堆因“直接安注”冷水注入压力容器下降环腔而导致的承压热冲击（PTS）热工水力问题,基于1:10比例模型,应用计算流体力学软件FLUENT5.4进行了紊流流动换热的数值模拟分析,同时进行了常压瞬态传热实验研究。针对下降环腔折算流速0.5 m/s,安注流速10m/s的典型工况,研究了安注水开启后下降环腔内的瞬态流动换热特性,数值模拟与实验结果吻合良好。考察了压力容器安注接管出口区环形焊缝区及堆芯段筒体中子强辐照区所承受的热冲击状况,基于稳态流动研究了下降环腔内流体混合特性及流动机理,为热冲击分析提供参考。     

Optical measurements of thermal diffusivity of a material

The measurement of thermal diffusivity of a material (in particular, a thin film) is important for various reasons, e.g., to predict the heat transfer in the solid subjected to a thermal process, to monitor surface composition or morphology, or to detect invisible subsurface defects like delaminations. This measurement can be done in a noncontact manner using various photothermal methods. Such methods typically involve pulsed heating of the surface by small amounts using a laser source; the decay of the surface temperature after this pulsed photothermal heating is then probed to provide the thermal diffusivity. Various probing methods have been developed in the literature, including the probing of reflection, refraction, and diffraction from the pulsed heated area, infrared thermal radiometry, and surface deformation. This paper provides an overview of such techniques and some examples of their applications.     

Experimental evaluation of the strength distribution of E-glass fibres at high strain rates

A bimodal Weibull distribution function was applied to analyse the strength distribution of glass fibre bundles under tensile impact. The simulation was performed using a one-dimensional damage constitutive model. The results show that there were two concurrent flaw populations in the fracture process. The regression analysis using the bimodal Weibull distribution function was in good agreement with experiment.     

微波热液法制备光催化TiO2功能材料

采用微波加热法，研究了钛配离子热分解水解反应的规律。结果表明，水解产物在大气气氛和300℃下煅烧2h，所得产物为锐钛型TiO2粉末。在紫外线照射下，乙酸经Ti02光催化反应12h后，残余量小于初始量的20％。     

提高热采注汽系统热效率的研究

为了降低热采成本和提高经济效益 ,建立了热采注汽系统热效率的数学模型。根据实测数据计算了 9个注汽系统的热效率。提出了改进注汽系统热效率的行之有效的措施。根据排烟的氧含量的大小 ,可以确定注汽锅炉热效率改进程度 ;按管线允许热损失量和保温材料种类 ,设计保温层厚度 ,可大大提高输汽管线热效率。仅此两项 ,即可使大部分注汽系统热效率提高 7%以上 ,井底蒸汽干度提高 10 %以上。     

Mycological and physical parameters for selecting suitable packaging material for pre- and post-irradiation storage of cereal grains in Ghana

Owing to the rough warehouse handling of storage sacks in tropical areas in Africa, a suitable storage sack should not support de novo growth of fungal spores because this would reduce the tensile strength of the packaging material and act as a springboard for infecting grain contents. This paper reports the effect of activity of saprophytic fungi on the tensile strength of jute and woven polypropylene sacks. New woven polypropylene sacks carried lower levels of fungal spores (1.3×10¹ cfu/72 cm²) than jute sacks (3.0×10³ cfu/72 cm²). The natural mould penetration and growth was examined on sections (4×5 cm) of both jute and woven polypropylene after previous incubation at relative humidities of 55, 60, 65, 70, 75, 80, 90 and 95% for 10 weeks by placing them on Sabouraud's Agar. There was a significant difference (P = 0.05 level of significance) between the higher penetration of mould growth on jute sacks and that obtained on woven polypropylene sacks. Saprophytic fungi (Aspergillus candidus, A. flavus, A. fumigatus, A. niger, A. japonicus, A. parasiticus, A. ustus, Fusarium oxysporium, F. moniliforme, Penicillium verucosum var. cyclopium, Rhizopus oryzae and Trichoderma viride) isolated from jute sacks reduced tensile strength, measured by an Instron Model 1026, by 50–75% after 10 weeks at 90% R.H. Same fungal species on woven polypropylene sacks did not alter the tensile strength. Woven polypropylene sacks did not absorb moisture whilst the moisture content of jute sacks increased by 5.3–6.0% in 10 weeks at 90% R.H. with concomitant increase in mould and yeast counts by 1–2 log cycles. Evidence is presented to show that there was a positive correlation between the final mycoflora on jute sacks and loss in tensile strength. No correlation, however, was found between the total aerobic bacteria on jute sacks and the concomitant reduction in tensile strength. Fungi therefore play a major role in the reduction of tensile strength of jute sacks. Sterilization by gamma irradiation (8.0 kGy) of jute and woven polypropylene sacks did not affect their intrinsic tensile strength. Woven polypropylene sacks therefore have many microbiological and physical advantages over the traditional jute sacks to merit their use for grain storage in tropical areas like Ghana.