表外储油层酸化防膨剂的评价及效果分析

本文论述了采用不同防膨试验方法评价不同类型粘土防膨剂,并以回归曲线和价值工程分析防膨效果。由分子结构理论提出分子保护膜的防膨机理新观点,论述了酸液中添加具有多种功能的非离子型防膨剂QC—1可提高表外储层酸化与排酸效果。     

Synthesis of diamond crystals and films using an oxygen-acetylene flame under atmosheric pressure

Diamond growth with rates up to 100 to 140 μm/hr was achieved using an oxygen-acetylene combustion spraying technique in an atmospheric environment. Investigations on the processing indicated that the gas flow ratio, substrate position, substrate temperature, temperature distribution, and substrate pretreatment were the most important factors affecting the growth of diamond crystals. Evaluation by means of X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and electron probe microanalysis showed that the synthesized diamond was nearly perfect in morphology, structure, and purity.     

电荷耦合图像传感器在细线直径测控系统中的应用

文中给出了一个以氟化氪固体激光器做光源，以电荷耦合图像传感器为光屏，应用夫朗禾费衍射原理，实现对细丝直径在线检测自动控制。该方案对相关企业质量控制的自动化是有意义的。     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

The optimal diamond wheels for grinding diamond tools

Grinding is the most suitable process for manufacturing good quality diamond tools. In this paper, diamond wheels have been studied. From the grinding of polycrystalline diamond (PCD) insets, the effects of certain factors such as the bonding material, the grit size and structure of a diamond wheel have been investigated. It is concluded that vitrified bond diamond wheels are the most suitable for grinding PCDs and the recommended grit size is mesh number 1000, which can get a good surface quality within an appropriate time. The wheel structure is another important factor. Rougher wheels (mesh #800, #1000) with the softer grade scale P yield a higher material removal rate (MRR) than scale Q. However, a finer wheel (mesh #1200) needs a tougher structure to promote its grinding ability and to have a higher MRR.     

Characterization of temporal response, spectral responsivity and its spatial uniformity in photoconductive diamond detectors

Three photoconductive diamond detectors with highly oriented diamond (HOD) films fabricated by the same process were characterized with respect to temporal response, spectral responsivity and its spatial uniformity over the wavelength range from 190 to 250 nm. Temporal measurements showed a drift in the baseline, suggesting the presence of deep level carrier traps. The responsivity of specimen No. 2 was more than twice those of the other two specimens, but it showed an unpredictable current fluctuation. It was found that the spatial uniformities of all the specimens were too low for radiometric purposes. A prominent peak, thought to be due to photoemission, was found in the responsivity spatial distribution of specimen No. 3 under a negative applied voltage.     

Comparative study of the electrical properties of diamond films grown by microwave plasma assisted and hot-filament chemical vapor deposition

Schottky diodes were built on different polycrystalline diamond films grown by Microwave Plasma and Hot Filament Chemical Vapor Deposition and their electrical properties were studied. The barrier height increased with the diamond film quality and the corresponding ideality factor decreased. Even though the lower-quality HFCVD film displayed poor rectifying properties, it was found to be much less sensitive to variations in the operating conditions (air vs. vacuum). The activation energies of the films depend on morphological parameters, as preferable grain size or orientation. The bulk conduction also depends on the quality of the deposited films, changing from ohmic to trap-free or shallow trap SCLC and SCLC with an exponential distribution of traps. The hypothesis of using the electrical measurements as an indicator for film quality has been discussed.     

Effect of temperature on the optical and electro-optical properties of poly(methyl methacrylate)/E7 polymer-dispersed liquid crystal composites

Experiments on the effect of temperature on the optical and electro-optical behaviors of polymer-dispersed liquid crystals (PDLCs) are considered. Composite films composed of poly(methyl methacrylate) (PMMA) and the nematic-type liquid crystal (LC) E7 were prepared by solvent casting in chloroform. The PDLC film contained droplets of E7 from 10 to 80 wt % in a PMMA matrix. Morphological studies illustrated the formation of isolated droplets of LC due to phase separation, and their homogeneous distribution increased with increasing E7 content. Thermo-optical studies showed an increase in the nematic–isotropic transition temperature of composites, which indicated preferential solvation during the phase-separation process. The electro-optical characteristics were studied under the conditions of an externally applied square wave electric field with a He–Ne laser (λ = 632.8 nm) as a light source. The responses improved as the E7 content in PMMA increased. Semipermanent memory effects were noticed in composites at higher temperatures. Changes in the transmittance due to thermal variations provided the possibility of using such a device as a temperature sensor. The results obtained indicate that under these experimental conditions, the output can be controlled to the desired level by the selection of a suitable loading of LC to prepare PDLC electro-optically active composite films with a response time on the order of only a few milliseconds. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

影响带锯机锯切质量的原因及处理措施

通过对锯切装置的改进，提高了锯切性能，降低了锯条成本，保证了锯切质量，使设备更加高效、安全的工作。     

论薄板坯连铸连轧产品质量优势

通过对薄板坯连铸连轧工艺的分析，深入研究了其产品的质量优势，同时还指出了在产品生产过程中需要重点注意解决的一些问题。