薄层隔热保温涂料的研制及应用

常规保温材料的研究以提高孔隙率、提高热阻、降低传导传热性能为主,但其对流传热及辐射传热较难降低。当今以传热机理改进保温材料及保温结构是重要发展方向。文章介绍了一种借鉴国外航天工业用高科技绝热涂层的技术思路,并结合国情研制成功的具有高辐射率的薄层隔热保温涂料,它可弥补常规保温材料的不足。该保温涂料以液态涂料方式存在,干燥后的涂层热阻较大,特别是热反射率高,可有效地降低辐射传热,施工方便,涂层薄,无接缝,附着力好,集防水隔热外护于一体。绝热等级为R21.1,热反射度0.79,热辐射率0.83,固含量54％,性能接近国外同类产品水平,成本仅为国外产品的1/4左右。可直接以涂层方式使用,也可与其他多孔保温材料复合构成低辐射传热结构,作为石油石化行业成品油罐及储罐的隔热保温、管道及设备的保冷及屋面隔热保温涂层使用,综合节能效益高。     

TbFe磁性薄膜的磁力显微镜成像研究

利用磁力显微镜（MFM）对TbFe磁性薄膜进行了不同抬举距离（分别为60～780nm）的磁力成像研究．在实验中，比较了低抬举距离（100nm以下）磁力像中样品-针尖的互相干扰；同时发现在高抬举距离磁力像中，随着抬举距离的增大，出现了与高凸起形貌对应的图像衬度特征，并随抬举距离的变化也改变着位置与强度，一直到抬举距离为仪器的极限值780nm时，形貌干扰仍未消失，对其形成机制进行了分析．     

焦粉四辊破碎机高硬度辊皮切削的新工艺

分析了高硬度辊皮的磨损情况；改进了辊皮的切削方案；满足了生产需求并提高了作业率。     

无氢类金刚石碳膜的研究进展

介绍了无氢类金刚石碳膜的制备方法 ,它们的机械、光学、电学性能 ,将无氢与含氢的类金刚石碳膜进行了简单比较 ,总结及探讨了它们的应用     

DDI法测薄膜光学常数

双光束双波长激光干涉（ＤＤＩ）法采用自行设计的可调双波长氦氖激光器作光源，可在同一光路中通过两次测量获得薄膜样品两个波长（０．６３３μｍ，３．３９μｍ）下的光学常数，即折射率、消光系数和厚度。论述了测量原理、测量装置和测量结果。     

定向凝固空心叶片制壳工艺的改进

分析了在先进发动机定向凝固空心叶片熔模精密铸造生产中出现两种缺陷的性质和产生原因，从壳型制造工艺方面提出了改进措施，提高了叶片合格率。     

热分解法制备钛酸铅镧薄膜及其电性能研究

本文研究了用金属有机物热发解法制备ＰＬＴ８薄膜的工艺过程和基片对薄膜结构的影响，并且给出了铁电性能的测量结果。     

The electron microscopy of post-growth induced defects of ZnSe/GaAs epilayers

A fundamental research of structural defects induced upon post-growth processing of ZnSe/GaAs epilayers grown on (100) GaAs was done by identifying defect-related reflections in the transmission electron diffraction (TED) patterns of ZnSe. Structural artifacts, other than the as-grown defects, on this material system could be excluded according to our results. Four types of abnormal reflections have been observed in addition to primary reflections. These extra reflections are sensitive to the post-growth processing of ZnSe epilayers and may arise from various external effects, rather than epitaxy growth, such as irradiation damage, surface oxidation, and surface contamination. By mapping these reflections at several major zone axes using TED patterns, we found that the reciprocal lattice for a ZnSe crystal with structural defects consists of two distinct types of extra reflections associated with irradiation damage. The first type of extra reflections is ±1/3{111} and the other is ±1/2{111} corresponding to pure-edge and non-edge dislocation loops, respectively. For (100) oriented wafers, the ±1/3{111} and ±1/2{111} reflections were observed only on two of the four possible 〈111〉 variants (i.e. [111]_Zn and [111]_Zn)and this phenomenon was attributed to the anisotropy of defect distribution. Extra reflections associated with surface oxidation and contamination are also observed. The orientation relationships between a surface hexagonal ZnO and a cubic ZnSe film are [0001]_ZnO//[−111]_ZnSe, and [01−11]_ZnO//[011]_ZnSe. The origin, characterization, and elimination of these induced reflections are discussed. With the knowledge about these extra effects on structural defect formation, we have shown the real microstructure of ZnSe epilayers.     

PECVD方法用于梯度薄膜材料的研究

本文研究了ＰＥＣＶＤ方法制备Ｓｉ－Ｏ－Ｍ系梯度薄膜材料，并运用计算机控制技术成功地制备了涂层折射率随膜深成正弦波形式连续变化的Ｒｕｇａｔｅ单通带滤波器样品。结果表明，采用ＰＥＣＶＤ方法可以制备性能上乘、结构复杂的梯度薄膜材料，ＰＥＣＶＤ方法在研究、开发高级光学涂层领域有着宽广的应用前景。     

格栅式水泥搅拌桩支护在西涌泵站的应用

简介水泥搅拌桩的支护机理,以西涌泵站为例介绍采用格栅式水泥搅拌桩作支护结构的设计及计算方法,指出该技术能较好地解决软湿粘性土地区枢纽深基础开挖问题.