石英砂加载混凝工艺的DOM去除特征与混凝机理

为处理未纳入管网的市政污水,采用石英砂加载混凝工艺,考察石英砂的粒径及其投加量对处理效能的影响,分析了溶解性有机物(dissolved organic matters,DOM)的去除特征,并探讨了石英砂加载混凝机理。结果表明,与常规混凝相比,当石英砂的粒径和投加量分别为200目和 1.0 mg/L 时,石英砂加载混凝工艺对污水中浊度、COD的去除率分别为97.55%、59.2%,优于常规混凝;石英砂加载混凝工艺可明显去除芳香类、共轭双键、疏水性有机物,主要促进了腐殖质类物质的削减;石英砂通过架桥作用增加了絮体的密度,进而显著改善了絮体的沉降性能、强度;絮体的沉降性能、强度及再稳性能随着石英砂粒径的降低而升高。     

Poly(oxyphosphazenes): A unifying look at structure and morphology

Variations in thermotropic behavior have been investigated for many crystalline polyphosphazenes. Experimental results obtained from DSC, solid-state MAS NMR, dilatometry, mechanical property (creep and dynamic) measurements, birefringence, X-ray (wide and small-angle), and electron diffraction have been made as a function of temperature in an attempt to elucidate the structure-morphology behavior in these polymers. Initially all polyphosphazenes described in this study crystallize from dilute or moderately concentrated solutions in the monoclinic form with relatively low crystallinity (50%). When heated, these specimens expand atT(1) and adopt a chain-extended 2D mesophase morphology in order to relieve congestion. Above this first-orderT(1) temperature a chain-extended –P=N– chain backbone morphology transforms into an isotropic phase at the melting temperatureT _m. When cooled, samples transform into the mesostate. However, crystallization from the mesophase belowT(1) takes place into a 3D orthorhombic state. These two modes of ordering/disordering are in accordance with (i) a hexatic chain packing [betweenT(1) andT _m] with variously mobile side groups that also exhibits smectic features when mesogenic side groups are present and (ii) a 3D orthorhombic structure of high crystallinity belowT(1). The initial monoclinic phase is accessible only via a solution crystallization route. Solid-state MAS NMR, crystallization kinetic measurements, and optical microscopy studies obtained from oriented and unoriented polymers have been especially germane in providing a unifying picture for mesophase formation and ordering in polyoxyphosphazenes. X-ray and electron diffraction evidence is complicated by critical overlapping peaks that are found under these same conditions. They demonstrate that (a) positional disorder exists along the chain direction and (b) the side chain above, as well as below, theT(1) transition is governed by the mobility, size, and type of side group in circumstances where phase transformations occur.     

改进的形态学运算在声纳图像生成中的应用

声纳技术应用日益广泛,已成为海洋测量的重要工具,而去除噪声处理是对声纳图像进行正确判读的前提,本文采用了改进的形态学算法减少声纳图像中噪声的影响,对图像进行预处理,采用Matlab图形图像处理工具对处理的算法进行仿真的方式,从而使处理效果达到最佳。     

Formation of WC/Ni hard alloy coating by laser cladding of W/C/Ni pure element powder blend

WC/Ni coating was formed by laser cladding of a W/C/Ni powder blend. The formed WC crystals have rectangular or quadrangle cross-section shapes with size of 2–30 μm. Step, twist and cross growth morphologies of WC formation were observed. The coating contains WC, CW_3, WNi, FeW₃C, Fe₆W₆C, W₃O, W, C, and (Fe,Ni) phases.     

钢表面化学气相沉积TiC晶体的择优取向

本文用化学气相沉积(CVD)法,以TiCl_4-CH_4-H_2为原料气体,在不锈钢表面获得了致密的TiC膜.研究了TiC的成膜速度、表面形貌和晶体择优取向与沉积条什的关系.结果表明,沉积温度T_(dep),碳钛比CH_4/TiCl_4强烈地影响了TiC的成膜速度、表面形貌和晶体择优取向.CH_4/TiCl_4低时,TiC晶体的择优取向为(220):而CH_4/TiCl_4高时,TiC晶体的择优取向为(200).TiC晶体的择优取向主要取决于气氛中活性碳的平衡浓度。     

立式钻铣床动力头设计与三维造型

多工位钻铣床实现了一台机床对一个零件做不同加工的功能,节省了机床,也缩小了占地面积,同时提高了加工精度和生产率,对工人劳动强度也降低很多。本设计中,钻头的固定采用拉杆式楔形固定,钻头采用套筒及主轴轴面为拉杆的结构,套筒外侧用绝缘胶固定了一个支撑架,钻头的动力由同步齿形带传递到钻头,比起万向轴传递动力要准确且刚性好。动力采用行星轮的传递方式,保证了各工位的同步工作,节省空间,本机构紧凑,各啮合齿轮之间中心距不超过100 mm,因而,用齿轮传动可以满足要求,这样可以用标准件对机床快速装配完工,对缩短加工周期有很大好处。     

强度传输方程和神经网络融合的三维重构算法

针对原有强度传输方程法所恢复的相位精度不够精确的缺点,提出强度传输方程和神经网络融合的三维重构算法. 利用强度传输方程求解出物体不同角度的初始相位,利用神经网络算法进行优化,根据不同角度的最终恢复相位结合乘法技术重构出三维体信息. 该算法具有精度高的特点,可以为三维成像技术的应用提供参考. 对于实验中的示例图像,该算法将强度传输方程得到的相位误差从21.40%降低为5.26%,重构三维物体与模拟真实物体的相关程度为显著相关.     

钼对渗碳过程中碳化物形态的影响

通过萃取复型观察和对衍射花样的标定，研究了深层渗碳过程中析出碳化物的形态和分布。实验结果表明：渗碳过程中析出的形态较好的碳化物，象点状、球状和椭球状碳化物均为钼的碳化物；而形态较差的针状、网状则为（Cr、Fe）7C3和（Fe，M）3C。并对其形成机理进行了初步探讨。     

基于阈值分割的松材线虫病树计数与定位

松材病虫病是最紧迫的威胁之一,最近对中国针叶林造成了严重破坏,为了阻止松材病虫病的快速传播,必须在早期准确检测和计数受感染的树木。提出了一种基于密度图的方法,用于从高分辨率航拍图像中估计具有松材病虫病的树木数量,方法引入了阈值分割、形态处理和超像素技术,以最大限度地减少由于建筑物和岩石等相似背景物体引起的误差。实验表明,所提出的方法优于密度学习 算法,平均绝对误差、均方根误差和绝对误差方差分别从21.3、22.2和127.2减少到8.0、11.7和59.6,计数准确率从54.7%提高到81.3%。     

N,N−二甲基−二硫代甲酰胺丙磺酸钠对THPED体系化学镀铜的影响

研究了N,N?二甲基?二硫代甲酰胺丙磺酸钠(DPS)作为添加剂对以四羟丙基乙二胺(THPED)为单一配位剂的化学镀铜体系的沉积速率、镀层形貌和晶体结构的影响。结果发现,当DPS的质量浓度从0 mg/L增大到1.0 mg/L时,沉积速率从2.91μm/h提高到6.73μm/h,所得镀层结晶均匀、细致。线性扫描伏安测量结果表明,DPS是通过促进甲醛的阳极氧化来加速化学镀过程。本体系的Cu镀层主要呈面心立方多晶取向,DPS的添加会令晶面取向从(220)转变为(111)。