The Effect of Post-Cooking Holding Times on Sensory Assessment of Low- and High-Fat Beefburgers

ABSTRACT: The effect of post-cooking holding-time on sensory assessment of low (89 g/kg) and high (218 g/kg) fat beefburgers was assessed. Burgers were served to panelists approximately 3 or 18 min after cooking. Fat content influenced fattiness, moistness/juiciness and overall appearance (P < 0.05), overall acceptability and overall texture (P< 0.01) and tenderness and crumbliness (p<0.001). Burgers with the higher fat content had higher scores. Holding-time influenced sensory overall appearance only with lower scores at extended holding times (P < 0.01). Treatment differences were small, mostly less than one sensory scale unit. Higher lightness and yellowness values were found for burgers with higher fat contents.     

紧凑型FLC光纤PDL模块

描述了紧凑型FLC（铁电液晶）光纤PDL（光子延迟线）模块的结构和运转特性；分析了插入损失；提出多信道运转时依赖于波长的设计方案。     

Development of a Sensor Fusion Strategy for Robotic Application Based on Geometric Optimization

Fusion of multi-sensor information is an important technology, which is growing exponentially due to its tremendous application potential in many areas. Effective fusion of data from sensors is very critical in increasing an intelligent system's capability to accomplish complex tasks. Appropriate fusion technologies are needed to be developed specially when a system requires redundant sensors to be used. More the redundancy in sensors, more is the computational complexity for controlling the system and more is its intelligence level. This research presents a strategy developed for multiple sensor fusion, based on geometric optimization. Each sensor's uncertainty has been modeled using classical Lagrangian optimization techniques. However, the uniqueness and effectiveness of the present technique lies on the fact that starting from the optimized value as initial estimate the accuracy of the sensory information has further been improved up to any pre defined bounded range, by developing two architectures – FFA (fission–fusion architecture) and FDD (fusion in differential domain). Sufficient evidences and analyses have been provided in the paper to show its effectiveness in various applications.     

液位定量式灌装机的灌装精度概率模型与可靠度计算模型

描述了控制液位定量式灌装机的灌装时间与灌装精度的关系，推导出实际灌装时间的理论计算公式。针对实际存在的各种随机变量对灌装时间的影响，建立了灌装时间的概率模型，提出基于灌装时间随机误差的灌状精度以及灌装精度可靠度概念，并相应建立出灌装精度概率模型与灌装精度可靠度计算模型。     

低渗透油藏生产井关井测压时间的计算与应用

低渗透油藏的生产井压裂后，在单井试油试采过程中，压力恢复测试关井时间不同，其中有些井压力恢复曲线不能出现边界反应段，渗流不能反映地层中真实流动特征。针对这种情况，基于长庆绥靖油田塞39井区长：低渗透油藏大量试井和实际生产资料，利用现代试井解释理论，研究合理关井时间的界限及其计算方法。结果表明，当油井关井测压时间达到3倍地层径向流开始出现的时间后，利用此时的压力数据解释地层参数和地层压力，其结果的误差小于5％，同时能较准确地判断边界类型。计算的理论曲线和霍纳法解释值非常接近，对于塞39井区，若预先知道某生产井地层有效渗透率值，可从理论曲线查出压力恢复试井的关井时间，否则，建议按照该井区地层有效渗透率（大约在6mD左右），将不稳定试井测试时间控制在25d以上为宜。图4表3参14     

Process Variables, Gelatinized Starch and Moisture Effects on Physical Properties of Mungbean Noodles

The effects of amounts of gelatinized starch and moisture in the final slurry or dough, cooking time, holding time, and holding temperature on physical properties of mungbean noodles were studied. Cooking loss, cutting stress, work to cut, and transparency of noodles were measured. Moisture content of the final slurry or dough, cooking time, and holding temperature were the most important factors that affected physical properties of mungbean noodles. Processing should be done at moisture contents not exceeding 55%, cooking times not longer than 40 set, and holding temperatures not lower than 3° using 5% of total starch as gelatinized starch and holding time of 36 hr.     

方波信号在音频技术中的应用

本文重点介绍了方波依赖在音频测量，设备的维护检测及录音均衡自动调节等音频技术中的应用，并通过对方波信号的频谱特性和方波信号通过线性系统的频域特性的分析，简要说明了方波信号在应用电路中的基本工作原理。     

一种混沌信号去噪方法的研究

以Takens嵌入定理和影子定理为理论依据，提出一种能对混沌信号去噪的局部投影方法。该方法不需潜在动力学系统的先验知识，符合工程实用的要求。通过实验结果表明这种方法对混沌信号去噪很有效。     

Techniques for estimating test length under random test

When a circuit is tested using random or pseudorandom patterns, it is essential to determine the amount of time (test length) required to test it adequately. We present a methodology for predicting different statistics of random pattern test length. While earlier methods allowed estimation only of upper bounds of test length and only for exhaustive fault coverage, the technique presented here is capable of providing estimates of all statistics of interest (including expected value and variance) for all coverage specifications.Our methodology is based on sampling models developed for fault coverage estimation [1]. Test length is viewed as awaiting time on fault coverage. Based on this relation we derive the distribution of test length as a function of fault coverage. Methods of approximating expected value and variance of test length are presented. Accuracy of these approximations can be controlled by the user. A practical technique for predicting expected test length is developed. This technique is based on clustering faults into equal detectability subsets. A simple and effective algorithm for fault clustering is also presented. The sampling model is applied to each cluster independently and the results are then aggregated to yield test lengths for the whole circuit. Results of experiments with several circuits (both ISCAS '85 benchmarks and other practical circuits) are also provided.This work was done while the author was with the Department of Electrical Engineering, Southern Illinois University, Carbondale, IL 62901.     

桩柱式采金船每帮挖方量的理论计算

本文从理论上推导出了桩柱式采金船每帮挖方量计算的数学模型并，可广泛地用于设计与生产中，从而提高采金船设计的准确性，以及对生产矿山进行矿量、回收率和实收品位等采选指标收测的可靠性。