显像管发射小的跟踪分析

本文对黑白显像管发射小进行了跟踪分析，认为阴极涂层脱落和管内真空度不良是导致显像管发射小的主要原因。     

涂层材料的断裂分析(英文)

和基体厚度相比,涂层很薄,因此细观力学模型可把基体作为半无限弹性体。由于涂层和基体材料的膨胀系数及弹性系数不匹配,涂层材料中残余热应力的解析解为 E_c/(1-γ_c)·(α_s-α_c)△T。用有限元法校核,该应力和解析解吻合得好。通过对涂层产生裂纹驱动力和断裂韧性的讨论,提出了抗裂涂层厚度公式。     

化学镀SiCp／Ni－P复合镀层与基体结合强度及其影响因素

论述了ＳｉＣｐ／Ｎｉ－Ｐ复合镀层与钢基体的结合强度及其影响因素。复合镀层中离界面５μｍ厚度以内区域的组成及应力状态对镀层／基体的界面结合有决定性作用，在该区域以外ＳｉＣ粒径变化不影响镀层的结合强度。适当的热处理可提高界面结合力。     

相转移法制备高纯超细TiO2技术研究

报道了用相转移法制备高纯超细ＴｉＯ２的新技术；探讨了Ｔｉ（Ⅳ）从有机相转移到水相发生水解反应的机理 ；通过ＴＧ－ＤＴＡ分析以及ＸＲＤ物相分析对水解产物的组成、热分解机理，晶型转变规律进行了研究，建立了水解产物焙烧的最佳温度。     

激光对陶瓷层的釉化处理

本文研究了激光重熔等离子体喷涂的陶瓷层。为了降低气孔率,获得好的微观结构和均匀性,减少覆盖材料的应力,提高涂层材料和基体的结合力,探讨了相间的结合机理,分析了重熔过程中出现的问题。     

一种碳－碳复合材料长寿命防氧化涂层的失效机制

用液相法联合ＣＶＤ法和硅化法制备了一种碳－碳复合材料复合梯度涂层，在此基础上对这种涂层在氧化过程中的失效机制进行了研究．结果表明：氧化层与液相层界面反应生成的气相产物是涂层失效的根本原因界面上气泡的不均匀形核、长大和破裂导致涂层表面出现孔洞．孔洞处气泡优先形核、长大和破裂并发展成为缺陷而使涂层失效     

The effect of pre-wetting on dynamic contact angles

A roll-coating experimental system is used to study the effect of pre-wetting on dynamic contact angles, the interfacial displacement depth, and the associated phenomenon of air entrainment. The system consists of a roll, which is horizontally rotating in a liquid pool. The dynamic contact angle is recorded by a macrophotography system. The test liquids are glycerol solutions with viscosities in the range 104 < μ < 748 mPa · s. The value of (μV/ρg)^0.5 is taken as the characteristic length to be used in the dimensionless relationships which correlate experimental measurements. The effect of base layer entry angle into the liquid pool on the dynamic contact angles and other flow parameters is studied. Comparison is made with measurements in dry tape-coating and other pre-wet roll–coating systems.     

An investigation of pore cracking in titanium welds

Two welded Ti-6A1-4V pressure vessels leaked prematurely in service. The leaks were caused by cracks emanating from weld porosity. The cracks originated during fabrication, with subsequent growth in service leading to the formation of the leak paths. Pore cracking is thought to be caused by a mechanism that involves both sustained-load and cyclic contributions, with the former being the more prominent. It is shown that the tendency for cracking is influenced by pore position and that pore size is not a deciding factor in that regard. The factors that govern pore cracking are discussed, and the possible role of interstitial embrittlement is assessed.     

Superplastic behaviour of Ti-48at.%Al two-phase titanium aluminide compacts made from mechanically alloyed powder

An HIP compact of MA-processed powder having a nominal composition of Ti-48at.% Al was produced. The compact consisted of a large amount of TiAl(λ) and a small amount of Ti₃Al (₂), in a completely ultra-fine equiaxed grain structure. This two-phase compact showed typical superplastic deformation behaviour. A maximum elongation of 550% was obtained. A strain exponent, n = 2, and grain size exponent, p = 2, were determined from the results of a strain-rate-change test and a creep test at constant initial stress using samples having various grain sizes, respectively. The activation energy for creep, Q_c at constant stress was calculated to be 350 kJ/mole. It is concluded that the superplastic deformation mechanism of the material under study is grain boundary sliding controlled by lattice diffusion in the TiAl phase.     

钛对耐硫变换催化剂性能的影响

利用常压微反色谱、程序升温还原（ＴＰＲ）等技术研究了钛对耐硫变换催化剂性能的影响，结果表明：（１）钛能明显提高耐硫变换催化剂的活性，尤其是在低于６２３Ｋ时活性提高最为明显；（２）工业侧流试验后，含钛样品的保留活性及活性保留率均高于Ｋ８－１１；（３）催化剂中添加助剂ＴｉＯ２后，能显著提高对原料气中Ｈ２Ｓ含量变化的适应能力，因此可以拓宽对原料气的选择范围，对工业生产有着十分重要的现实意义。