碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.     

石墨化率不同的自焙炭块的热膨胀

采用精密垂直拉杆膨胀仪在１４～１０００℃范围内测量了具有不同石墨化率的自焙炭块的相对热伸长量，并由此获得了热线膨胀系数α。结果表明：石墨化率一定时，α值在较低温度下随温度升高而增加，在较高温度下，α值随温度变化不明显；恒温时，石墨化率越高，α值越低。讨论了单位热应力下的弹性模量概念     

Spheroidization of medium-carbon steels

Spheroidization experiments were made on a medium- carbon AISI 4037 steel, using both intercritical and subcritical annealing cycles. The results indicate that in the subcritical cycle the spheroidization occurred much more quickly than expected, so that shorter times were sufficient to achieve high formability. On the other hand, the hardness dropped faster in the intercritical cycle. Although more work needs to be done, these results suggest that using a subcritical spheroidization process instead of an intercritical process could achieve considerable savings in time, energy, and cost.     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

Influence of volatile matter and deposited carbon on coke yield from coals

The relations between coke yields and the volatile matter content of 30 individual and 30 blended coals were investigated. Coke yields and deposited carbon related to volatile matter content can be expressed in the following equations: CY (%) = 97.89?0.86 VMch+VMc; and DC (%)= ?2.24+0.16 VMch; where: CY=real coke yield; VMch = volatile matter content of charging coal; VMc=volatile matter content of coke, and in the case of <2%; DC = deposited carbon. The test results show excellent correlation with practice.     

High resolution XPS characterization of chemical functionalised MWCNTs and SWCNTs

High resolution XPS analysis of chemical functionalised multi-wall carbon nanotubes (MWCNTs) and single wall carbon nanotubes (SWCNT) was done with ESCA300 (overall instrument resolution of 0.35 eV). Information to the degree of functionalisation was ascertained by argon ion bombardment of the samples followed by XPS analysis to detect the functional groups, the percentage atomic concentration of various elements present and whether or not the detected functional groups imposed a chemical shift on the CNT atoms. The results show that true chemical functionalisation was achieved and by argon ion bombardment these functional groups can be altered relative to the C 1s carbon atoms of the CNT. The choice of chemicals used for functionalisation, the techniques employed and the types of nanotubes treated are important factors in chemical characterisation. The carbon atom on the nanotube ring to which the functional group (atom) is bonded, the chirality of the CNT, the electronegativity of the functional group, the bond type and whether the CNT is single-wall or multi-wall, or cut (short) could play a role in determining the chemical shift on the CNTs atoms. These investigations are relevant to chemical functionalisation of carbon nanotubes for various applications for example DNA sensors and other biomedical sensors.     

Fenton试剂处理苯酚和甲醛废水的研究

用H2O2同Fe^2 结合的Fenton试剂处理有机废水是一种经典的催化氧化法，这种方法适合于处理废水中高浓度、难降解的有机物质。主要研究了Fenton试剂处理含苯酚和甲醛有机废水样的反应机理和影响因素，试验结果表明：废水中苯酚和甲醛的去除率均可达到95％以上，COD去除率达到85％以上，表明用Fenton法处理含苯酚和甲醛的有机废水是一种非常有效的方法。     

Degree of crosslinking and mechanical properties of crosslinked poly(vinyl alcohol) beads for use in solid-phase organic synthesis

The limited swellability in polar media of the commonly used polystyrene/divinylbenzene (PS-DVB) support materials for solid-phase organic synthesis has led to the development of novel, highly swellable hydrophilic gels designed for use in aqueous or polar media. Poly(vinyl alcohol) beads crosslinked with epichlorohydrin (PVA-EP) were prepared by a two-step inverse-suspension polymerization method. While it is known that the morphology of the resulting beads can be controlled by the ratio of EP versus PVA as well as by the pre-crosslinking time, the actual degree of crosslinking of the beads and their mechanical properties remain unknown. It is therefore the purpose of this study to evaluate the actual degree of crosslinking of beads prepared with different quantities of crosslinker in the feed by spectroscopic (Raman, nuclear magnetic resonance) and chemical (functional group loading) methods. The mechanical properties of these swollen PVA-EP beads will be evaluated by single-bead unconfined compression in solvents such as water, N,N-dimethylformamide (DMF), and tetrahydrofuran (THF) and compared to model PS-DVB beads commonly used for solid phase synthesis.     

Consequences of different cutting regimes on regrowth and nutrient stoichiometry of Sparganium erectum L. and Potamogeton natans L.

Aquatic vegetation forms an essential component in freshwater ecosystems but due to changed environmental and anthropogenic conditions often needs management to reduce nuisance for human land‐use. In this paper, the authors looked at the regrowth of two macrophyte species (Potamogeton natans and Sparganium erectum) in two lowland rivers under different cutting treatments. After an initial cross‐sectional transect was manually removed from bank to bank at the beginning of the growth season, a monthly repetitive removal of biomass in plots on that transect was done during the rest of the growth season (testing frequency of mowing). Additional new transects were also cut in subsequent months (testing timing of mowing). Finally, biomass was repetitively removed in plots in those additional transects too (testing frequency of mowing × timing of mowing). The biomass at the end of the growth season was analysed for C, N, P, and Si. It was demonstrated that timing and frequency of vegetation cutting has an important effect on the capacity and rate of species' recovery and therefore on the efficiency of the applied management. Nutrient stoichiometry of the regrown biomass was directly affected by cutting. Caused by differences in the applied timing and frequency of the cutting, C/N and N/P ratios and BSi concentrations were highly variable. Yet, overall, there was a clear tendency towards a higher C/N ratio and BSi concentration and lower N/P ratio in biomass that recovered after cutting. This human impact on the quantity and quality of autochthonous organic matter may have knock‐on effects on the decomposers food web and mineralization process.     

Kinetics of the methanation of carbon dioxide over a supported Ni-La2O3 catalyst

The kinetics of the methanation of carbon dioxide was investigated using an alumina supported Ni-La₂O₂ catalyst in a differential and integral reactor. In the differential reactor the molar ratio of H₂ to CO₂ was varied from 0.6 to 30. In the integral reactor the rates were measured with up to 90% conversion. Both reactor tests were carried out at temperatures between 513 and 593 K. The experimental results were described by a Langmuir-Hinshelwood type equation. The kinetics can be explained by assuming equilibrium of dissociative carbon dioxide and hydrogen adsorption, and assuming hydrogenation of surface carbon as the rate determining step.