Skeletal Isomerization and Inter—molecular Hydrogen Transfer Reactions in Catalytic Cracking

Bimolecular hydrogen transfer and skeletal isomerization the important secondary reac-tions among catalytic cracking reactions,which affect product yield distribution and product quality,Catalyst properties and operating parameters have great impact on bimolecular hydrogen transfer and skeletal isomerization reactions .Bimolecular hydrogen transfer activity and skeletal isomrization activity of USY-containing catalysts are higher thn that of ZSM-5-containing catalyst.Coke deposition on the active sites of catalyst may suppress bimolecular hydrogen transfer activity and skeletal isomer-ization activity of catlys in different degrees.Short raction time causes a decrease of hydrogen trans-fer reaction,but and increase of skeletal isomerization reaction compared to cracking reaction in catalytic cracking process.     

碱式苦味酸铅针刺药的应用研究

提出了以碱式苦味酸铅为主体的针刺药在组合点火管中的应用，并对其针刺药的点火性能及能量传递进行了讨论，阐明了此类针刺药良好性能和应用价值。     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

高质量ZnO薄膜的退火性质研究

在LP－MOCVD中，我们利用Zn(C2H5)2作Zn源，CO2作氧源，在（0002）蓝宝石衬底上成功制备出皮c轴取向高度一致的ZnO薄膜，并对其进行500℃-800℃四个不同温度的退火。利用XRD、吸收谱、光致发光谱和AFM等手段研究了退火对ZnO晶体质量和光学性质的影响。退火后，（0002）ZnO的XRD衍射峰强度显著增强，c轴晶格常数变小，同时（0002）ZnOX射红衍射峰半高宽不断减小表明晶粒逐渐增大，这与AFM观察结果较一致。由透射谱拟合得到的光学带隙退火后变小，PL谱的带边发射则加强，并出现红移，蓝带发光被有效抑制，表明ZnO薄膜的质量得到提高。     

Si衬底上Ta-N/Cu薄膜性能研究

对Si衬底上Ta-N/Cu薄膜进行了电学和热学分析，结果发现500℃以下薄膜电随几乎不变，600-690℃下的退火引起的电阻率降低是由于Ta-N电阻的热氧化和Cu熔化扩散引起的，而690℃以上的电阻率增加是由于Cu引线传输能力减弱所致，为0.18μm以下的超大规模集成电路中的Cu引线和电阻薄膜的制作提供了有益的借鉴。     

PVD涂层工艺在M3滚刀上的应用

对M3滚刀进行了物理气相沉积 (PVD)工艺试验。经高温耐磨试验和切削试验证明 ,M3滚刀经TiN涂层后 ,其耐磨性和使用寿命显著提高。     

双跨换热器传热管在静水中阻尼特性的研究

本文对双跨换热器传热管在静水中的结构阻尼与粘滞阻尼作了简介,并对在总阻尼中占主导地位的挤压膜阻尼作了较深入的讨论。Mulcahy 于80年代初提出的挤压膜阻尼数学模型是较为完善的,其缺陷是未计入管子振幅的影响,本文对它进行了修正。为了验证理论分析的结果,笔者对双跨传热管在静水中的挤压膜阻尼作了实验研究,得出挤压膜阻尼与中间支承板厚度、管子-中间支承板间隙以及管子振幅之间的关系。     

Effect of Pressure Gradient on Heat Transfer of Impinging Submerged Circular Jets

An experimental and numerical study have been carried out to investigate the distribution of radial local heat transfer coefficients of impinging submerged circular jets. Good agreement is achieved between the experimental results and the predicted value. Results show that the outer peak usually occurs at the radial location of r/d= 1.8~2.0, in which transition from laminar to turbulence happens resulting from disappeared pressure gradient abruptly, and that the inner peak appears rigidly at r/d=0.5, where the boundary layer has a minimum thickness because of elevating pressure gradient.     

Technology transfer projects in developing countries—furthering the Project Management perspectives

This paper attempts to broaden the analysis of the technology transfer phenomenon by refocusing research attention on the level of performance assessment of technology transfer projects. An holistic evaluation framework based on the considerations of an extended Project Life Cycle model is proposed to overcome some of the shortcomings of conventional approaches to project evaluation. This also reinforces the need for open systems thinking in assessing and managing risk of technology transfer projects. The discussion is based on two case studies which articulate the experiences with two integrated mechanisms of technology transfer used in Algeria from 1965 to 1990: turnkey and “product-in-hand”. The aim is to gain a better understanding of the processes of technology transfer and to contribute to the improvement of associated managerial practices in developing economies.