Effect of thermophoresis on particle deposition rate from a natural convection flow onto a vertical wavy plate

This research discusses the impacts of the surface area that the wavy surface gets more than the flat plate upon the aerosol particle deposition. Starting from the full Navier–Stokes equation, the mathematical analysis takes the thermophoretic motion formed by the temperature gradient and the fluid thermal expansion into consideration, and converts the governing equations into the boundary layer equation by the simple coordinate transformation and non-similarity method, and then works out these equations by the Spline Alternating-Direction Implicit method (SADI). The numerical value result reveals that the average deposition effect of the wavy plate is greater than the flat plate and that the increasing rate is nearly equal to the value obtained by dividing the surface area that the wavy plate gets more than the flat plate by 2.2.     

ROI-based Watermarking Scheme for JPEG 2000

A new region of interest (ROI)-based watermarking method for JPEG 2000 is presented. The watermark is embedded into the host image based on the characteristics of the ROI to protect rights to the images. This scheme integrates the watermarking process with JPEG 2000 compression procedures. Experimental results have demonstrated that the proposed watermark technique successfully survives JPEG 2000 compression, progressive transmission, and principal attacks.     

Research on the Distant Hybrids of Wheat Obtained via Low-Energy Ion-Beam Implantation

Abstract The whole DNA of soybean was implanted into four varieties of wheat of Zhongyu5, Huaiyin 9628, Wenyou 1, Jimai 5 respectively via ion-beam mediation. There were 5 plantsobtained whose protein content was higher than 18.5%, the highest one was 21.44%. There were 3plants obtained whose protein content was lower than 11.5%, the lowest one was 10.96%. We cansee that the whole DNA of soybean transformed into wheat via ion beam implantation can inducethe increase in wheat protein content dramatically. The result also shows that the transformationefficiency of different gene types of wheat receptor varies greatly that the implanting time has acertain effect on the efficiency of transformation.     

化学镀Ni—P镀层的X射线衍射研究

根据X射线衍射分析结果,对化学镀高P(含P>11wt％或19at％)Ni-P镀层加热时效时,镀层成分和加热温度对结构转变的影响作了研究,结果表明,高P共晶、过共晶(含P>11wt％或19at％)合金的结构转变有如下特征:(1)相同加热时效条件下,Ni-P合金的结构转变与成分有密切关系:(2)对同一成分的过共晶合金,Ni-P合金的结构转变与时效温度密切相关;(3)过共晶合金在290～360℃温度范围内时效处理,出现Ni_xP_y介稳相,X射线衍射分析认为Ni_xP_y为Ni_(12)P_5。     

Effect of plasticity on the residual stress measurement using the groove method

The mechanical methods based on milling rectilinear or annular grooves on a component's surface and measurement of relaxed strains are some of the most used semi-destructive methods for the determination of residual stresses. These are evaluated from the relaxed strains by means of equations based upon the linear elastic theory. In this paper the errors due to yielding localised at the bottom of the groove have been investigated. The analyses were carried out by means of the finite element technique varying the most important parameters involved. The experimental results show a good agreement with the numerical ones.     

Dynamic elastic-plastic behaviour of whipping pipes: experiments and theoretical model

This paper is concerned with the problem of pipe whip, the dynamic response of a high pressure piping system subjected to an end force as the result of a pipe break which releases a jet of fluid from the broken section. Both experimental and theoretical results are presented concerning the dynamic elastic-plastic behaviour of cantilever pipes subjected to a transverse force pulse at the free end. Comparisons between experimental data and theoretical predictions are made for mild-steel pipes with outer diameter-to-thickness ratios of 19.5, 28 and 32. It is demonstrated that, for these geometries, the whipping pipes display three characteristically different responses, viz. elastic, plastic hardening behaviour for thick pipes, elastic, plastic hardening-softening behaviour for moderately thick pipes and elastic, plastic hardening-softening-collapse behaviour for thinner pipes. The experimental data taken from a series of high-speed films are compared with the predictions of the instantaneous shapes of the whipping pipes derived from both a rigid, perfectly-plastic, large deflection, dynamic beam model and a more comprehensive model which incorporates the effects of elasticity and plastic hardening and softening, the details of which are presented in the paper.     

粒界缓冲型展宽效应对PTC材料温度系数的影响

本文利用相变扩张理论分析了粒界缓冲型展宽效应对BaTiO_3系PTC陶瓷的介电系数及温度系数a_r的影响,指出了晶粒尺寸和温度系数的关系。     

冷却速度对激光相变组织分布的影响

提出通过改变边界换热条件，从而改变冷却速度，达到控制激光相变硬化。实验和计算结果的比较表明，这种控制相变及其组织分布的方法能够处理激光淬火难以解决的问题。     

提高16Mn连铸坯控轧合格率

１６Ｍｎ连涛坯进行控轧时，按铸坯碳当量的上限和下限，分别采用两种不同的控轧制度。在邯钢中板分厂试轧的结果，轧材合格率均达到９６％以上，投产后轧材合格率达到９８％以上。     

The IS Organization of the Future: Four Scenarios for 2020

Four scenarios for the IS organization of 2020 are described, based on differing assumptions about two drivers: the advances in the reliability of international telecommunications and the value placed on computerization in businesses and society.