Prediction of liquid film mass transfer coefficients in packed columns using liquid holdup

A unique characteristic linear dimension (d), defined as the cube root of the specific liquid holdup (h_sp) in the packed column, was used to correlate successfully the liquid film mass transfer coefficient k_La for gas absorption-desorption for sparingly soluble gases in liquids below loading. To produce this simple, dimensionless correlation, k_La data reported in literature were used, covering a wide range of physical properties of liquids, packings and operating conditions. This new approach showed operating holdup as an important factor in gas liquid mass transfer.     

Carbon molecular sieve films produced by dc sputtering

This paper reports adsorption measurements that show molecular sieve effects in amorphous hydrogenated carbon (a-C : H) films deposited by d.c. magnetron discharge decomposition of acetylene. Adsorption of organic gases on the films is studied by using a quartz crystal microbalance technique. The sieve effect in this material depends on both deposition and annealing conditions. Films having significant molecular sieve effects are found to be typically microporous and to have a very small characteristic micropore dimension. It is suggested that the d.c. sputtered a-C : H film may be useful as a molecular sieve material in selective adsorption and gas permeation studies.     

Mullite for Structural, Electronic, and Optical Applications

Mullite (3Al₂O₃·2SiO₂) is becoming increasingly important in electronic, optical, and high-temperature structural applications. This paper reviews the current state of mullite-related research at a fundamental level, within the framework of phase equilibria, crystal structure, synthesis, processing, and properties. Phase equilibria are discussed in terms of the problems associated with the nucleation kinetics of mullite and the large variations observed in the solid-solution range. The incongruent melting behavior of mullite is now widely accepted. Large variations in the solid solubility from 58 to 76 mol% alumina are related to the ordering/disordering of oxygen vacancies and are strongly coupled with the method of synthesis used to form mullite. Similarly, reaction sequences which lead to the formation of mullite upon heating depend on the spatial scale at which the components are mixed. Mixing at the atomic level is useful for low-temperature (<1000°C) synthesis of mullite but not for low-temperature sintering. In contrast, precursors that are segregated are better suited for low-temperature (1250° to 1500°C) densification through viscous deformation. Flexural strength and creep resistance at elevated temperatures are significantly affected by the presence of glassy boundary inclusions; in the absence of glassy inclusions, polycrystalline mullite retains >90% of its room-temperature strength to 1500°C and displays very high creep resistance. Because of its low dielectric constant, mullite has now emerged as a substrate material in high-performance packaging applications. Interest in optical applications mainly centers on its applicability as a window material within the mid-infrared range.     

Preparation of micro-patterned surfaces of Si-N-O films and their influence on adhesion behavior of endothelial cells

Microgrooves were prepared on Si(100) surface by photolithography and wet etching.Subsequently,Si-N-O films were deposited on the microgrooves by unbalanced magnetron sputtering(UBMS) and micro-patterned surfaces of Si-N-O films were obtained.The size of the micropatterns was measured by surface profilometer.The chemical composition of Si-N-O films were characterized by X-ray photoelectron spectrometry(XPS) and the wettability of the micropatterned surfaces was evaluated by contact angle measurement.The beh...     

Investigation on film cooling characteristics from a row of converging slot-holes on flat plate

Experimental and numerical researches were conducted to investigate the cooling performance of a single row of consoles (converging slot-hole) on a large-scale flat-plate model. The results show that the coolant flow from a row of consoles shows good lateral uniformity of adiabatic effectiveness, with regions of slightly enhanced cooling occurring between the consoles. For the console cooling geometry, the interaction between coolant jet from inclined console and the mainstream flow results in reasonable vo...     

高速钢表面PN＋PVD复合处理工艺和性能研究

采用多弧离子镀设备,在高速钢W18Cr4V上先进行等离子氮化,再沉积TiN薄膜,研究了不同渗氮温度和时间对PN＋TiN薄膜组织和性能的影响。结果表明,温度为500℃左右和时间为2h以上条件下对W18Cr4V进行渗氮处理后再沉积TiN薄膜,可以得到最佳的薄膜表面显微硬度（1800～2000HV0.05）和膜／基结合力（50N）,涂层耐磨性也得到明显提高。     

Mixed convection heat and Mass transfer in a vertical channel with film evaporation

Numerical results are presented for effects of latent heat transport associated with film vaporization on laminar mixed convection heat and mass transfer in a vertical channel with a half channel width b = 0.01 m. The influences of the inlet liquid mass flowrate and wall temperature on the film vaporization and the associated heat and mass transfer characteristics are examined for air-water and air-ethanol systems with gas Reynolds number Re_g = 2000. Predicted results obtained by including transport in the liquid film are contrasted with those where liquid film transport is neglected, showing that the assumption of an extremely thin film made in Lin et al. (1988) and Yan and Lin (1989) is only valid for systems having small liquid mass flow rates. Additionally, it is found that the interfacial heat flux is predominantly determined by latent heat transfer connected with film evaporation.     

A novel electroless silver depositing method for magnesium alloys

Depositing silver on magnesium alloy by both electroless plating and organic coatings was studied. The organic coating was made by immersing samples in organosilicon heat-resisting varnish. In this method the organic coating acts as interlayer between the substrate and silver film. When the reaction starts, silver deposits directly on the interlayer. X-ray diffraction and SEM analysis were used to determine the composition and morphology of the interlayer and silver film. The potentiodynamic polarization curves for corrosion studies of coated magnesium alloys were performed in a corrosive environment of 3.5% NaCl（mass fraction） at neutral pH （6.9）. The results indicate that compared with the substrate, the corrosion resistance of coated magnesium alloys increases greatly. Moreover, the method proposed in this work is environmentally friendly, non-toxic chemicals were used. In addition, it provides a new concept for the corrosion inhibition of magnesium alloys.     

Preparation and characterization of TiO2 photoelectrode codoped with aluminum and boron and its application in dye-sensitized solar cell

Nanocrystalline titania films codoped with aluminum and boron were prepared by cathodic vacuum arc deposition. In the process, titanium alloy target was used under an O2/Ar atmosphere, and sensitization of films were carried out by natural dye-sensitized complex in anhydrous ethanol. The structure, surface morphology and UV-vis spectra of titania films codoped were measured by X-ray diffraction analysis, scanning electron microscopy and ultraviolet-visible spectrometer. Theas-deposited films are found to be amorphous. The films annealed were examinedto be of anatase structure with orientation along the (101) planes, the averagecrystal size is in the range between 41 and 45 nm. SEM results show that thereare some pores in the codoped titania films, the optical properties of the dye-sensitized films were also measured which reveals that the spectral responses of films shift to the visible region. Under simulated sunlight illumination, the overall energy conversion efficiency of dye-sensitized nanocrystalline solar cell is 0.9%.     

Influence of electroplating conditions on magnetic properties of Fe-36wt.% Ni alloy film

A Fe-Ni soft magnetic film was prepared in sulphate solution by electroplating. The influences of the molar ratio of n [Fe2+ ]/ n [Ni2+ ], current density, bath temperature, pH and L-ascorbic acid concentration on magnetic properties of Fe-Ni alloy film were investigated. The results show that the saturated flux density(BS) of the film increases initially and decreases after it reaches the specific value with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density, bath temperature and pH. However, the relationship between L-ascorbic acid concentration and B S keeps linear. It is observed that the coercive force( Hc) is enhanced with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density and pH. By comparison, when the bath temperature increases, Hc always decreases. With the increase of L-ascorbic acid concentration, the coercive force increases initially and then decreases.