PLC在环锭捻线机上的应用

介绍了如何使用PLC和数字变频调速技术 ,对传统环锭捻线机进行技术改造 ,使锭速、捻度和卷绕成形变换实现数字化柔性控制 ,扩大了工艺参数的变化范围 ,使整个捻线加工车间实现信息化管理成为可能。     

煤矸石高路堤下多孔拱涵顶进

介绍了国内首例煤矸石高路堤下顶进工程的施工     

Solids Extraction of Cod Frame and Effects on Ultrafiltration of the Aqueous Extract

Grinding, pH adjustment, heat treatment and centrifugation were studied to recover solids from ground cod frames and to apply ultrafiltration (UF) to the resulting aqueous phase. Early heat treatment (90°C/20 min) dissolved collagen into aqueous phase resulting in a very low UF flux. A pH adjustment to 4.5 after grinding (～0.32 cm die), with no heat resulted in efficient separation after centrifuging. UF of the aqueous phase showed an increase in initial flux (23 L/hr m²). However, when the same aqueous material was heated and then centrifuged (1–2% solids removed), UF flux was further increased to 46 L/hr m²and this process gave highest solids recovery (90%).     

合山电厂3个机组主厂房定向爆破拆除

介绍了广西合山电厂 1#～3# 机组主厂房定向爆破设计与施工.该工程不仅规模大、环境十分复杂、工期紧、难度高、风险性极强,最大特点是拆除发电设备与爆破同步进行施工.     

Interactive key frame selection model

Video summarization can provide a fine representation of the content of video stream and reduce a large amount of data involved in video indexing, browsing, and retrieval. Moreover, Key frame selection is an important step in the research of content-based video analysis and retrieval. Although there exist a variety of methods for key frame selection, they are heuristic and closed systems, which cannot dynamically generate video summary with user’s preference. In this paper, an M-estimator and epipolar line distance constraint camera motion estimation algorithm is introduced as camera parameters is an important motion feature for key frame selection, and Broyden-Fletcher-Goldfarb-Shanno (BFGS) method is applied to optimize estimated parameters. Moreover, since Interactive Computing is a novel-computing model that represents the transition of algorithm to interaction, an interactive model of key frame selection (IKFS) is presented as a result of improving the model of key frame selection (KFS). The model of KFS and IKFS are proved to satisfy the criterion of induction and coinduction, respectively. Experimental results show that the processing scheme generates flexible and desirable summarizations whose distortion rate is lower than current method. Above all, IKFS is an extension to KFS.     

Casual reasoning in planning1

Reasoning about actions necessarily involves tracking the truth of assertions about the world over time. The SIPE planning system retains the efficiency of the STRIPS assumption for this while enhancing expressive power by allowing the specification of a causl theory. Separation of knowledge about causality from knowledge about actions relieves operators of much of their representational burden and allows them to be applicable in a wide range of contexts. The implementation of causal theories is described, together with examples and evaluations of the system's expressive power and efficiency.     

基于改进PSO算法的结构损伤检测

结构的损伤检测常转化为求解约束优化问题,针对粒子群算法容易出现早熟问题,增大算法后期的粒子位置的改变量,从而增加粒子位置的差异,因而能够增强其在求解约束优化问题时抵抗局部极小的能力。两层刚架单损伤和多损伤识别的数值结果和收敛曲线表明了改进后的粒子群算法优于传统的带惯性因子的粒子群算法。三层框架结构的4种损伤工况的试验研究进一步说明了该算法应用于结构损伤检测领域的有效性。     

钢筋混凝土框架-剪力墙结构在强震作用下的非线性分析——Ⅱ、程序及算例

运用文献[1]所介绍的分析原理与方法,编制了强震作用下钢筋混凝土框架-剪力墙结构非线性地震反应时程分析的程序。本文介绍该程序的功能、框图,以及利用该程序计算所得到的几栋钢筋混凝土结构的非线性地震反应分析结果。算例表明,本程序计算结果可靠,能很好地用于解释震害和预测地震时结构可能发生的破坏。     

PLC在原料系统的应用

阐述了硅铁生产中焦碳生产输送系统的工作原理和工艺要求，介绍了PLC在原料输送系统中的应用，给出了PLC的I／O接线图及程序框图，提出了工业原料生产输送控制系统的设计特点。     

基础锚栓预埋加固方案

结合工程实例 ,介绍轻钢结构系统基础锚栓预埋、加固解决方案 ,并介绍了加固系统的制作及使用方法 ,可供工程人员参考