Ultrasonic-assisted drilling of Inconel 738-LC

Generally in the drilling of modern aviation materials such as nickel and titanium base super alloys, problems frequently occur in terms of burr formation at the cutter exit, tool stress, high heat generation on tool surface as well as low process reliability. A recent and promising method to overcome these technological constraints is the use of ultrasonic assistance, where high-frequency and low-amplitude vibrations are superimposed on the movement of cutting tools. This paper presents the design of an ultrasonically vibrated tool holder and the experimental investigation of ultrasonically assisted drilling of Inconel 738-LC. The circularity, cylindricity, surface roughness and hole oversize of the ultrasonically and conventionally drilled workpieces were measured and compared. The obtained results show that the application of ultrasonic vibration can improve the hole quality considerably. Improvements of up to 60% have been achieved.     

Cu48Zr4l7块体非晶合金的晶化行为及热力学性能研究

采用水冷铜模吸铸工艺制备出了片状Cu48Zr45Al7,块体非晶合金.X射线衍射(XRD)表明,样品为完全非晶.利用差示扫描量热分析仪(DSC)在不同的升温速率下连续加热测得该片状非晶合金的热稳定性参数值,均随着升温速率的增加而增加,表明其玻璃转变和晶化行为均存在显著的动力学效应.运用Kissinger法计算出其玻璃转变温度激活能(Eg)、晶化温度激活能(Ex)和峰值温度激活能(Ep)分别为424.7 kJ·mol-1,326.3 kJ·mol-1和297.1kJ·mol-1.从热力学模型角度出发,对该合金的非晶形成能力进行了分析,计算出其混合焓ΔHchem=-25.55 kJ.mol-1和归一化错配熵So/kB=0.78.结果表明,该块体非晶合金具有较强的非晶形成能力(AFA)NI良好的热稳定性.     

Complement-Opsonized Nano-Carriers Are Bound by Dendritic Cells (DC) via Complement Receptor (CR)3, and by B Cell Subpopulations via CR-1/2, and Affect the Activation of DC and B-1 Cells

The development of nanocarriers (NC) for biomedical applications has gained large interest due to their potential to co-deliver drugs in a cell-type-targeting manner. However, depending on their surface characteristics, NC accumulate serum factors, termed protein corona, which may affect their cellular binding. We have previously shown that NC coated with carbohydrates to enable biocompatibility triggered the lectin-dependent complement pathway, resulting in enhanced binding to B cells via complement receptor (CR)1/2. Here we show that such NC also engaged all types of splenic leukocytes known to express CR3 at a high rate when NC were pre-incubated with native mouse serum resulting in complement opsonization. By focusing on dendritic cells (DC) as an important antigen-presenting cell type, we show that CR3 was essential for binding/uptake of complement-opsonized NC, whereas CR4, which in mouse is specifically expressed by DC, played no role. Further, a minor B cell subpopulation (B-1), which is important for first-line pathogen responses, and co-expressed CR1/2 and CR3, in general, engaged NC to a much higher extent than normal B cells. Here, we identified CR-1/2 as necessary for binding of complement-opsonized NC, whereas CR3 was dispensable. Interestingly, the binding of complement-opsonized NC to both DC and B-1 cells affected the expression of activation markers. Our findings may have important implications for the design of nano-vaccines against infectious diseases, which codeliver pathogen-specific protein antigen and adjuvant, aimed to induce a broad adaptive cellular and humoral immune response by inducing cytotoxic T lymphocytes that kill infected cells and pathogen-neutralizing antibodies, respectively. Decoration of nano-vaccines either with carbohydrates to trigger complement activation in vivo or with active complement may result in concomitant targeting of DC and B cells and thereby may strongly enhance the extent of dual cellular/humoral immune responses.     

基于ArcReLU激活函数的优化研究

对常用的激活函数进行了研究比较。对曾经提出的一种新型激活函数ArcReLU进行了改进,使其具有更快的收敛速度和更低的计算消耗。实验证明,改进的ArcReLU函数既能显著加快反向传播神经网络的训练速度,又能有效降低训练误差,甚至能避免梯度消失的问题。     

超声辅助激光修复镍基高温合金V形槽

为了提高失效零件的修复质量,以V形槽为修复对象开展研究,在修复过程中引入超声振动. 耦合声场、温度场与流场建立超声辅助激光修复V形槽的非线性瞬态模型,对修复过程熔池形貌及其温度场进行数值模拟,并开展相关实验研究,分析超声对修复区组织及性能的影响机制. 数值模拟结果表明,超声振动能加速熔池流动与散热,提高熔深,细化晶粒并改善V形槽底部难熔区域的修复效果. 金相、扫描电子显微镜和电子背散射衍射分析结果表明,在超声作用下,晶粒尺寸和一次枝晶间距得到细化,Laves相更加弥散,Nb元素的富集受到抑制;常温和高温硬度在超声作用下分别提高了11.1%、10.4%. 研究表明,超声振动能有效改善镍基高温合金V形槽激光修复区的微观形貌,提高力学性能.     

水工混凝土构件裂缝检测方法及应用

水利工程在长期运行过程中,其混凝土构件会出现磨蚀、裂缝等损伤,如这类问题不能够及时得到处理,将会严重影响水利工程的安全运行。本次研究主要针对水工混凝土构件中的裂缝检测方法进行研究,提出从“定性”到“定量”的一体化检测思路,具体实施过程分为四部分,即“普探—详查—判定—验证”,其中,普探阶段采用探地雷达法,确定裂缝的总体分布;详查阶段采用超声横波反射三维成像的方法,确定裂缝的纵深向分布;判定阶段分别采用裂缝测宽法和表面声波法,用来确定裂缝的表面宽度和贯穿深度;验证采用钻孔电视,确定探测结果的正确性和准确性。上述技术路线突破了单一方法的限制,可有效地运用于水工混凝土构件裂缝检测,经实践证实,具有良好的检测效果。     

细磨活化对白钨矿浸取行为的影响SCIEI

本文研究了细磨活化对白钨矿浸取行为的影响.实验结果表明,细磨活化后白钨矿在HCl-Na_3PO_4介质中的浸出速率显著加快,钨的浸出率由原来的约8％提高到99％以上.红外光谱和X射线分析结果表明,细磨除了使白钨矿比表面积显著增大外,还在固体的表面和内部产生缺陷结构,增加了矿物表面的反应活性,改善了白钨矿的分解,使得白钨矿的浸出能在较低的温度顺利进行。     

Activation of hydrogen storage materials in the Li–Mg–N–H system: Effect on storage properties

We investigate the thermodynamics, kinetics, and capacity of the hydrogen storage reaction: Li₂Mg(NH)₂ + 2H₂  Mg(NH₂)₂ + 2LiH. Starting with LiNH₂ and MgH₂, two distinct procedures have been previously proposed for activating samples to induce the reversible storage reaction. We clarify here the impact of these two activation procedures on the resulting capacity for the Li–Mg–N–H reaction. Additionally, we measure the temperature-dependent kinetic absorption data for this hydrogen storage system. Finally, our experiments confirm the previously reported formation enthalpy (ΔH), hydrogen capacity, and pressure–composition–isotherm (PCI) data, and suggest that this system represents a kinetically (but not thermodynamically) limited system for vehicular on-board storage applications.     

汽车喷烤漆自动控制系统

本文通过研究目前汽车烤漆房的实际运行情况，提出了一种汽车烤漆房喷漆自动控制系统，阐述了系统喷漆装置的构成、配合与运行原理，并构成了实际试验系统。     

超声加工中振幅衰减的控制

超声加工过程中，振动系统的振幅会发生衰减，造成加工过程不稳定，生产率降低。针对振幅衰减的原因，提出了先进行频率跟踪，然后在谐振状态下再提高振幅的方案，使振幅不因加工状态的变化而变化，从而保证加工质量，提高生产率。