节能建筑中人体传热模型和计算公式

讨论人体新陈代谢发热率及其影响因素;论述节能建筑中舒适的环境温度、空气相对湿度、空气流速以及新鲜空气供给量的最佳值范围;同时考虑皮肤和肺部的显热散热和蒸发潜热散热,建立了传热模型,得出了计算公式。     

管内覆丝网强化对流换热及阻力特性的实验研究

通过实验对管内覆丝网管进行了强迫对流换热和阻力特性研究。结果表明：管内覆丝网使换热明显增强，阻力也相应增长。菱形丝网对角线距离与平行边距离之比对换热效果有决定作用，丝网厚度对换热的影响比较小，而丝网网格的大小对换热几乎没有影响，在相同的泵功率和几何条件下，换热系数最大增加２１％。     

铸铝激光熔融处理后的组织与性能

应用光学和电子显微镜及显微硬度计研究了铸造Al-Si合金经激光表面熔融处理后的组织和性能。指出,组织分熔化区、过度区和基体三层。在熔化区中树枝状先共晶α相的平均宽度由原始组织的20～40μm细化到2～3μm,同时共晶组织也被大大细化。这些变化使显微硬度值由67.4提高至109～115.     

Calculation methods for comparing the performance of pure and mixed working fluids in heat pump applications

Three methods for comparing cycle performance of working fluids, pure as well as non-azeotropic mixtures, are investigated for two applications and for two mixture pairs, HCFC22-CFC114 and HCFC22-HCFC142b, and their pure components. The methods differ in the way of calculating the heat exchange processes. They assume, respectively, equal minimum approach temperatures, equal mean temperature differences and equal heat transfer areas. Changes of coefficient of performance (COP) with composition are explained for all methods. It is shown that transport properties must be taken into account when making rigorous comparisons between working fluids. To predict the relations between fluids with high accuracy, one must use the method with equal heat transfer areas. By the method with equal mean temperature differences, the COP can be estimated with the same accuracy for mixtures as for pure fluids, and can be used for rough estimations of the COP level with different fluids. The method of equal minimum approach temperatures should be avoided for non-azeotropic mixtures.     

K418B合金细晶铸造整体涡轮真空热处理工艺研究

通过力学性能评估和金相组织观察，研究五种热处理制度，两个周期的试验结果，确定了Ｋ４１８Ｂ合金细晶铸造整体涡轮的真空热处理工艺。     

本钢烧结矿冷却及其余热回收的试验研究

从烧结矿冷却并回收其余热的角度出发，介绍了利用烧结机尾落矿空间，采用喷吹空气装置对烧结矿进行冷却的小型模拟试验，从测出的结果来看，有可能成为一种新的烧结矿冷却方式。     

低温导热绝缘胶粘剂研究

一种低温导热绝胶粘剂用于氢氧发动机系统表面温度传感器的端封和胶接安装，介绍了胶粘剂的技术要求，研究方案及试验结果。以DW－3超低温胶粘剂为基础，经改性设计后，仍能保持胶粘剂原有的耐低温特性，而且其导热，绝缘等性能均能满足设计和使用要求。     

Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

Subsecond thermophysics research at the Boris Kidrich Institute Vincha

In the early eighties, at the Boris Kidrich Institute Vincha, a method for measuring specific heat and electrical resistivity of electrical conductors in the millisecond resolution range was developed for measurements from room temperature to 1900 K. Over a period of nearly 10 years, the method was applied to different materials, including pure metals, ferrous, and nickel/ chromium alloys, and to the characterization of candidate materials for thermophysical property reference standards. This paper describes the method and reviews the results obtained in specific heat and electrical resistivity studies of ferromagnetic and other materials. The paper also demonstrates capabilities of the method for describing phase transitions or anomalies in pure metals (Fe, Co, Ni) or alloys (Nichrome, austenitic stainless steel).Paper presented at the Second Workshop on Subsecond Thermophysics, September 20–21, 1990, Torino, Italy.     

冷却速度对激光相变组织分布的影响

提出通过改变边界换热条件，从而改变冷却速度，达到控制激光相变硬化。实验和计算结果的比较表明，这种控制相变及其组织分布的方法能够处理激光淬火难以解决的问题。