裂齿矩形翅片板翅式换热器优化设计的分析

对裂齿矩形翅片板翅式换热器中的裂齿矩形翅片的传热效率作了分析,并以单位质量材耗的换热能力最大为目标函数,分析研究了在不同雷诺数(Re)的操作条件下裂齿矩形翅片间角度、翅片厚、长度、宽度及极厚之间的关系。结果表明:在气体换热的场合下,当Re在某一范围时翅片可有效地起到强化传热的作用。当板厚为5mm,翅片厚为3mm,翅片间夹角为45°～70°,Re为2×10~3～8×10~3,最佳翅片纵向间距与翅片长度和翅片厚度乘积的平方根的比为1.5～2.5,最佳翅片尺寸系数为3～5时,传热强化效果较好。     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

长距离温泉输水管道设计

福州市首次把城市外围的温泉水引入市区,本文简要介绍长距离温泉输水管道设计中一些做法。     

汽轮机叶片用X20Cr13钢的热处理工艺研究

采用正交试验对汽轮机叶片用X20Cr13钢进行了热处理工艺研究，以获得该钢的最佳热处理工艺，并在回火后以不同的速度冷却，以揭示冷却速度对钢的回火脆性的影响。结果，X20Cr13钢的最佳热处理工艺为900℃油淬或风冷，670℃回火，风冷。     

RMT1-250转换开关用电接触材料

铜铬锆合金是一种形变热处理材料，兼具了铜铬合金和铜锆合金的各种优良性能，经过时效处理的铜铬锆合金，与铜相比，高温强度有很大的改善，而且具有较高的导电率。所以铜铬锆合金广泛应用于电焊机、低压电器等行业。根据对铜铬锆成分的适当调整，可用作为电焊机电极，低压电器触桥、短路环等各种电接触材料。铜铬锆合金用于RMT1－250转换开关，接近于触桥材料的应用，但使用的条件更苛刻一些，要承受部分电弧的侵蚀和由此产生的高温，因此对材料要求具有良好的导电导热性和更高的高温强度。     

Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

The Difference in Turbulent Diffusion between the Active and Passive Scalars in a Thermally Stably Stratified Medium

The difference in the turbulent diffusion between the active (heat) and passive (mass) scalars in a thermally stably stratified medium is investigated. The axisymmetric problem is treated on the formation of a turbulent circulation flow above a heated disk and on the turbulent diffusion of a passive scalar (impurity) from a continuous surface source in a stably stratified medium. The results indicate that the thermal stratification causes appreciable differences in the coefficients of turbulent transfer between the active (heat) and passive (mass) scalars. This means that the assumption of the identity of the coefficient of turbulent diffusion of heat and mass, employed in conventional models of turbulence, produces significant errors in estimating the heat and mass transfer in a thermally stably stratified medium.     

Performance of unitary heat pumps: review of ASHRAE Symposium session

1. 1. System design optimization and validation for single-speed heat pump by S.K. Fischer and C.K. Rice, Oak Ridge National Laboratories.

2. 2. Analysis of on/off cycling for an air-to-air heat pump operating in the heating mode by W.A. Miller, Oak Ridge National Laboratories.

3. 3. Field measured cycling, frosting and defrosting losses for a high efficiency air source heat pump by V.D. Baxter and J.C. Moyers, Oak Ridge National Laboratories.

4. 4. Design and available energy analysis of a heating-only residential heat pump for the Western Pacific Northwest by D.E. Elger, C.M. Reistad and S. Lang, Oregon State University.

5. 5. A study of heat pump service life by Nance C. Lovvorn, Alabama Power Company and Carl C. Hiller, Electric Power Research.

垂直管吸收器内泡式吸收过程的数值研究

建立垂直管吸收器管内泡式吸收过程中传热传质的数学物理模型，对其泡式吸收过程进行数值研究，获得泡式吸收方式的一些传热传质特性，为吸收器的优化设计提供一定理论指导。     

热处理对Ti-25V-15Cr-2Al-2Mo-0.2C合金组织稳定性的影响

研究了热处理对Ti-25V-15Cr-2A1-2Mo-0.2C阻燃β钛合金组织稳定性的影响。结果表明，高温固溶并直接时效处理导致合金β基体上析出较多的α相沉淀，尤其在随后的热暴露组织中形成了恶化合金塑性的连续晶界α膜。然而，若在时效前再进行一次低温固溶处理则可明显减少α相的析出数量，合金的热稳定性因此而得到显著改善。