焊接构造对T型接头超低周疲劳性能的影响

为了研究焊接细节对钢结构超低周疲劳性能的影响,以T型接头为对象,在通用有限元程序Abaqus平台上,开发基于Arlequin算法的结构多尺度计算程序. 利用多尺度算法,开展焊接接头的局部弹塑性有限元分析. 比较焊趾半径、厚钢板未熔透长度及焊趾表面凹凸对局部塑性应变履历的影响,利用Coffin-Manson模型对T型接头的超低周疲劳特性进行定性讨论. 数值计算结果表明,焊趾位置是焊接接头的超低周疲劳易损位置,厚钢板的未熔透长度对焊接部位局部塑性应变的影响不大;焊趾半径对焊趾局部塑性应变有较大的影响,增大焊趾半径可以有效提升钢结构在循环荷载下的超低周疲劳性能;焊趾表面的平整性是影响焊趾局部塑性应变履历的重要因素,尖锐的凹坑会明显降低焊接接头的超低周疲劳性能,磨平的焊趾表面可以减少局部塑性应变,提高接头的超低周疲劳强度.     

高强度结构钢的韧性启裂和稳态扩展

研究了具有一定韧度的高强度结构钢裂纹早期扩展阻力与材料的微观组织结构、应力状态、变形历史和应变特性之间的关系。结果表明:裂纹扩展阻力(指J_R阻力曲线中的J_i和dJ/da)主要决定于裂纹尖端的塑性约束程度和应力应变场中消耗的弹性能和塑性功。这与三轴应力状态函数σ_mσ~(1/2)有关。材料的流变曲线描述了形变过程中的变形历史和应变特性,有明显的阶段性,其中第Ⅱ阶段的变形历史和应变特性制约着裂纹的启裂过程,第Ⅲ阶段的变形历史和应变特性制约着裂纹的扩展过程。应变硬化率dσ/dε可以敏感地反映出材料内部的应力分布和微观断裂机制。     

管无芯弯曲中塑性变形规律的研究

通过大量管材弯曲试验,分析了沿弯曲线的切向和管壁厚方向的应力应变状态,给出弯管内、外侧管壁厚变化量和切向应变的近似计算公式。在后续试验的基础上,逐步将修正公式适用于实际生产。同时,为管材弯曲成形机理研究作了相应的基础准备工作。     

On certain aspects of strain rate sensitivity of sheet metals

The formability of a material depends upon the strain hardening and strain rate hardening of the material. In this study, constitutive parameters using the power law constitutive equation are determined for six different strength steels and two aluminum alloys over different strain ranges, including approximations of the postuniform elongation range. Constitutive parameters are found to be different at different strain ranges. The strain hardening of steels increases with strain at low strain levels (less than 5%) and decreases at high strain levels (greater than 10%). Strain rate hardening decreases with strain for all steels and aluminum alloys. Uniform elongation depends only on strain hardening, and postuniform elongation depends only on strain rate hardening. However, the total elongation depends on both strain hardening and strain rate hardening.     

Ti-22Nb-6Zr(at%)合金的超弹性和形状记忆效应

用弯曲法和拉伸法测定Ti-22Nb-6Zr（at％）合金的超弹性和形状记忆效应，研究固溶处理温度对Ti-22Nb-6Zr合金组织结构及性能的影响。结果表明：固溶处理后Ti-22Nb-6Zr合金的室温组织为单一的β相，晶粒尺寸随固溶处理温度升高而增大；合金的静态弹性模量小于30GPa；Ti-22Nb-6Zr合金具有良好的超弹性和一定的形状记忆效应。室温下变形，合金的超弹性和形状记忆效应随固溶处理温度升高而提高。900℃固溶处理后的合金在室温下拉伸变形，应变为5％时，总的最大回复应变达4．12％，其中超弹性回复应变为3．91％，记忆回复应变为0.21％。     

铸钢件准固态区域应力,应变数值模拟及热裂机制

对ＺＧ４５实验热裂试棒的数种工况进行了应力－应变的数值模拟，对热裂形成机制进行了讨论。研究认为：热裂起源于Ｂｉｎｇｈａｍ体，是塑性变形超过Ｂｉｎｇｈａｍ体塑性储备值所致。     

Analytical and experimental analysis of deep drawing process for bimetal elements

The paper presents the concepts of solving of deep drawing process for bimetal elements of sheet materials. The inertia forces, plastic hardening behaviour of the deformed material and dynamic stress are utilized in the problems of plasticity. The experimental results and general conclusion are presented at the end of the paper.     

基于有限元分析的轮胎胎圈耐久性能优化

以新开发的175/70R14半钢子午线轮胎为研究对象,针对胎体帘布反包端点裂口问题建立有限元仿真模型。根据有限元分析结果提出增大胎体帘布反包端点高度的改进措施。结果表明,增大胎体帘布反包高度能够有效改善胎圈裂口现象,提高胎圈耐久性能;有限元分析结果与试验结果有很好的一致性。     

Experimental determination of gas holdup and volumetric mass transfer coefficient in a jet bubbling reactor

The hydrodynamics and mass transfer characteristics of a lab-scale jet bubbling reactor(JBR) including the gas holdup, volumetric mass transfer coefficient and specific interfacial area were assessed experimentally investigating the influence of temperature, p H and superficial gas velocity. The reactor diameter and height were 11 and 30 cm,respectively. It was equipped with a single sparger, operating at atmospheric pressure, 20 and 40℃, and two p H values of 3 and 6. The height of the liquid was 23 cm, while the superficial gas velocity changed within 0.010–0.040 m·s~(-1) range. Experiments were conducted with pure oxygen as the gas phase and saturated lime solution as the liquid phase. The liquid-side volumetric mass transfer coefficient was determined under unsteady-state oxygen absorption in a saturated lime solution. The gas holdup was calculated based on the liquid height change, while the specific interfacial area was obtained by a physical method based on the bubble size distribution(BSD) in different superficial gas velocities. The results indicated that at the same temperature but different p H, the gas holdup variation was negligible, while the liquid-side volumetric mass transfer coefficient at the p H value of 6 was higher than that at the p H = 3. At a constant p H but different temperatures, the gas holdup and the liquid-side volumetric mass transfer coefficients at 40℃ were higher than that of the same at 20℃. A reasonable and appropriate estimation of the liquid-side volumetric mass transfer coefficient(kla) in a pilot-scale JBR was provided which can be applied to the design and scale-up of JBRs.     

细菌纤维素的功能化改性研究进展

细菌纤维素(BC)是微生物生长过程中产生的以葡萄糖为基本骨架的结构性碳水化合物,具有高纯度、高聚合度、高结晶度、高持水性、高抗张强度和良好的机械强度,在功能材料领域显示了巨大的应用潜力.综述了近年来BC合成菌种筛选的研究现状;分析了BC在透气、吸湿排汗、力学性能和染色与脱色性能调控方面的进展情况;重点总结了BC基材料在抗菌、防紫外线、防辐射、防静电、拒水拒油、导电和传感等功能化改性方面的研究进展;最后,指出BC大规模高效成模和成型技术、差异化高功能BC材料制备技术是未来的重点研发方向.