扩展接触器零部件通用性的研究

本文介绍了一种只用十几个分立元件的电子模块，与大型接触器配合使用，可使接触器节省铜线材料60％～70％，大大减少电磁系统的体积。预置电子模块的参数，可实现交流接触器在起动过程、吸持过程的最佳电流控制，为扩展接触器零部件通用性研制出节能、节材、无噪声等性能优良的小型而容易实施的交流接触器产品提供了依据。     

适用于扩展有限元裂缝计算的钢筋与混凝土粘结滑移关系

以定量分析钢筋与混凝土粘结滑移关系为目标,利用RCXFEHohai-P扩展有限元程序,计算采用不同粘结滑移公式时钢筋混凝土简支梁的最大裂缝宽度。结果表明,计算所得最大裂缝宽度各不相同,且都与《混凝土结构设计规范》(GB 50010—2010)所列最大裂缝宽度公式计算值存在差别。为此,基于GA-BP神经遗传网络,以规范最大裂缝宽度公式计算值为预测目标,反演得到适用于扩展有限元裂缝计算的粘结滑移公式,算例表明该公式能满足扩展有限元裂缝宽度计算要求。研究成果对提高扩展有限元裂缝分析的准确性具有一定的参考价值。     

破碎覆岩回采巷道临界宽度研究

为了有效控制破碎覆岩回采巷道变形,根据其赋存特征采用工字钢架棚支护技术,分析破碎覆岩普氏拱结构的形成原理和研究回采巷道临界宽度。针对破碎覆岩回采巷道具有围岩破碎、强度低和不具有可锚性等特点,采用普氏拱理论,计算回采巷道围岩压力;当棚梁工字钢最大正应力等于工字钢屈服极限时推导出破碎覆岩条件下回采巷道临界宽度计算公式。以106煤矿为工程实例进行分析,结果表明：破碎覆岩回采巷道的合理临界宽度为4.4m;增大支护强度和减小巷道高度可有效提高破碎覆岩回采巷道临界宽度;如果需要更大的巷道宽度,可通过降低棚间距或增大型钢型号方法实现。     

真空粉末绝热低温贮罐制造的部分工艺方法

在真空粉末绝热低温贮罐的制造过程中、通过吸附器分子筛的活化、夹层真空系统的处理和充装珠光砂等工艺方法的改进,可较大地缩短产品的制造周期并提高产品的质量。     

考虑边界反射的河流离岸排放污染混合区计算方法

在等强度点源离岸排放条件下,从简化二维移流扩散方程的解析解出发,探讨了考虑两岸反射作用的中宽河流污染混合区的计算方法。给出了污染混合区边界形状曲线与量纲一方程的形式;采用迭代计算和试算比较法,给出了靠岸与离岸两种类型混合区各几何特征参数(坐标)、面积及面积系数与相对离岸距离的关系曲线,提出了以相对离岸距离a'作为判据的排放类型分区条件。给出了河流岸边、离岸与中心排放的分类判别准则:(1)当0≤a'≤a'1时,简化为岸边(近岸)排放类型;(2)当a'1a'a'2时,称为离岸排放类型;(3)当a'2≤a'≤0.5时,简化为中心排放类型,并给出了岸边排放类型与离岸排放类型的临界相对离岸距离a'1和中心排放类型与离岸排放类型的临界相对离岸距离a'2的表达式。通过回归分析,给出了中宽河流离岸排放类型混合区主要特征参数的实用计算公式,可作为中宽河流污染混合区范围计算和排污口位置优化设计的依据。     

虚拟场景中有宽度物体移动路径的优化方法

提出一种虚拟场景中有宽度物体移动路径的优化方法,在地图掩码数据经过寻路算法搜索后,得到一组连续路径节点组成的节点集,从起始节点出发,沿着路径节点找出离起始节点最远且没有障碍物遮挡的可见节点,作为下一个起点,循环往复直至节点集的终止节点,并顺序连接这些可见节点,即可得到优化路径。通过合并节点集中的多余节点,使路径更平滑,从而减少物体移动过程中改变方向的次数,解决有宽度物体无法通过狭窄通道后,须重新计算路径的问题,达到了更好的用户体验效果。     

The study on the conductivity of styrene-maleic anhydride copolymer electrolytes based on poly(ethylene glycol)400 and LiClO4

Polyelectrolytes, in this study were synthesized from styrene-maleic anhydride (SMA) copolymer, poly(ethylene glycol)400 (PEG400), and lithium perchlorate (LiClO₄). Fourier transform infrared spectroscopy (FTIR), and magic angle spinning (MAS) solid-state NMR were used to monitor the interaction between Li⁺ ions and polymer. The results of FTIR and MAS solid-state NMR indicate the Li⁺ ions are preferentially coordinated to the ether oxygen of PEG. The T_g of the PEG segments in polyelectrolyte increases with LiClO₄ concentration, as determined by differential scanning calorimetry (DSC), indicating that solubility of the Li⁺ ions in the host polymer increases with the PEG content. Impedance spectroscopy (IS) shows that the bulk conductivity of polyelectrolytes and the conductivity behavior obeys the Vogel-Tamman-Fulcher (VTF) equation.     

<Emphasis Type="Italic">In situ</Emphasis> monitoring of solid fat content by means of pulsed nuclear magnetic resonance spectrometry and ultrasonics

An ultrasonic technique was developed to study the crystallization process of edible fats on-line. A chirp wave was used instead of the conventional pulser signal, thus achieving a higher signal-to-noise ratio. This enabled measurements to be made in concentrated systems [≈20% solid fat content (SFC)] through a 8.11-cm thick sample without significant signal loss. Fat samples were crystallized at 20, 25, and 30°C at a constant agitation rate of 400 rpm for 90 min. The crystallization process was followed by ultrasonic spectroscopy and a low-resolution pulsed nuclear magnetic resonance spectrometer. Specific relationships were found between ultrasonic parameters [integrated response, time of flight (TF), and full width half maximum] and SFC. TF, which is an indirect measurement of the ultrasonic velocity (v), was highly correlated to SFC (r ²>0.9) in a linear fashion (v=2.601 SFC+1433.0).     

A surrogate-based optimization method with RBF neural network enhanced by linear interpolation and hybrid infill strategy

In engineering, it is computationally prohibitive to directly employ costly models in optimization. Therefore, surrogate-based optimization is developed to replace the accurate models with cheap surrogates during optimization for efficiency. The two key issues of surrogate-based optimization are how to improve the surrogate accuracy by making the most of the available training samples, and how to sequentially augment the training set with certain infill strategy so as to gradually improve the surrogate accuracy and guarantee the convergence to the real global optimum of the accurate model. To address these two issues, a radial basis function neural network (RBFNN) based optimization method is proposed in this paper. First, a linear interpolation (LI) based RBFNN modelling method, LI-RBFNN, is developed, which can enhance the RBFNN accuracy by enforcing the gradient match between the surrogate and the trend observed from the training samples. Second, a hybrid infill strategy is proposed, which uses the surrogate prediction error based surrogate lower bound as the optimization objective to locate the promising region and meanwhile employs a linear interpolation-based sequential sampling approach to improve the surrogate accuracy globally. Finally, extensive tests are investigated and the effectiveness and efficiency of the proposed methods are demonstrated.     

HYDRODYNAMIC STUDIES IN A HALF SLOT-RECTANGULAR SPOUTED BED COLUMN

Experiments were carried out in a half slot-rectangular spouted bed to investigate the effects of slot width and lower section basal angle on column hydrodynamics. Flow regimes, minimum spouting velocity, spouting and maximum pressure drops, and maximum spoutable bed height were determined for 4 mm diameter polyethylene particles. The results are compared with those for conventional cylindrical and rectangular spouted beds. Correlations for each hydrodynamic parameter are developed and compared with equations available in the literature.