女性护理液抗炎止痒作用的实验研究

女性护理液为中药苦参醇提液加三氯羟基二苯醚复配而成，根据药理方法学以实验动物建立模型，观察护理液的抗炎、止痒作用。结果，单独使用三氯羟基二苯醚，有较好的抗菌消炎作用，但是止痒作用不明显。以苦参醇提液和三氯羟基二苯醚复配，其抗炎、止痒作用均接近地塞米松磷酸钠注射液。     

改性磷石膏球作缓凝剂对水泥性能的影响

研究了工业化生产的改性磷石膏球对水泥标准稠度用水量、凝结时间、胶砂流动度、胶砂强度及水泥与减水剂相容性的影响,并与原状磷石膏和天然石膏进行对比,结合X-射线衍射、综合热分析等微观测试,分析了改性磷石膏球对水泥水化产物相、水化程度的影响.结果表明:采用改性磷石膏球配制的水泥,其初凝、终凝时间与掺配原状磷石膏水泥相比分别缩短217 min、227 min,1d、3d强度显著高于原状磷石膏配制的水泥,28d强度高于天然石膏配制的水泥,且标准稠度用水量、胶砂流动度、与减水剂的相容性等指标优于天然石膏配制的水泥.改性磷石膏球对水泥早期水化无不良延缓作用,且能提高水泥后期水化程度.综合对比上述三种石膏对水泥性能影响的各项指标,认为改性磷石膏球可以完全替代天然石膏作水泥缓凝剂.     

Event-driven,pattern-based methodology for cost-effective development of standardized personal health devices

Experiences applying standards in personal health devices (PHDs) show an inherent trade-off between interoperability and costs (in terms of processing load and development time). Therefore, reducing hardware and software costs as well as time-to-market is crucial for standards adoption. The ISO/IEEE11073 PHD family of standards (also referred to as X73PHD) provides interoperable communication between PHDs and aggregators. Nevertheless, the responsibility of achieving inexpensive implementations of X73PHD in limited resource microcontrollers falls directly on the developer. Hence, the authors previously presented a methodology based on patterns to implement X73-compliant PHDs into devices with low-voltage low-power constraints. That version was based on multitasking, which required additional features and resources. This paper therefore presents an event-driven evolution of the patterns-based methodology for cost-effective development of standardized PHDs. The results of comparing between the two versions showed that the mean values of decrease in memory consumption and cycles of latency are 11.59% and 45.95%, respectively. In addition, several enhancements in terms of cost-effectiveness and development time can be derived from the new version of the methodology. Therefore, the new approach could help in producing cost-effective X73-compliant PHDs, which in turn could foster the adoption of standards.     

个人洗护用品配方原理及应用技术(Ⅱ)--护肤品配方原理及应用

从护肤品配方原理、各类配方成分(如乳化剂)介绍和其应用等方面讨论护肤品开发应用的相关注意要点，并给出了参考配方。     

Alkali release characteristics of blended cements

This paper presents results of an experimental program conducted to investigate the capacity of hydration products of different cementing materials to retain “bound” alkalis when the alkalinity of the surrounding solution drops. The study covered paste samples containing high-alkali Portland cement and various levels of silica fume and/or fly ash. The results showed that the ability of the hydration products of cement-fly ash systems to bind alkalis is a function of the CaO content of the fly ash, the binding increasing as the calcium content decreases. High-alkali fly ashes (Na₂O_e > 5.0% and CaO in the range of 15% to 20%) showed considerable amounts of alkali contributed to the test solutions. Silica fume does not have a high capacity to retain alkalis in its hydration products; however, ternary blends containing silica fume and fly ash have excellent capacity to bind and retain alkalis.     

汽车用橡胶制品的发展

介绍了橡胶制品应用于汽车中的现状，统计了各种汽车中的橡胶用量、汽车橡胶制品使用的胶种及比例、世界汽车年产量，橡胶消耗量，轮胎生产量及世界前30名橡胶制品企业销售额。对汽车用橡胶制品的特点及发展趋势作了较系统的介绍。     

Reaction products of ammonium nitrate phosphate fertilizers of varying water-soluble phosphorus content in different Indian soils

Studies were undertaken on the isolation and identification of reaction products of ammonium nitrate phosphate (ANP) fertilizers containing 30, 50 and 70 per cent water-soluble phosphorus (WSP) of total phosphorus in representative soils of the vertisol, oxisol, alfisol, entisol, mollisol and aridisol groups of India. ANP fertilizers were applied in solid form to soil, and reaction products formed at and around the site of ANP fertilizer placement were identified after six weeks incubation in moist soils by X-ray diffraction technique. DCPD (dicalcium phosphate dihydrate- CaHPO₄ · 2H₂O) was the major reaction product of ANP fertilizers containing 30 and 50 per cent WSP in vertisol, entisol, aridisol, mollisol, oxisol and alfisol, and of ANP containing 70 per cent WSP in vertisol, entisol, alfisol, aridisol and mollisol. DCP (dicalcium phosphate-CaHPO₄) was detected with ANP of 30 and 50 per cent WSP in the vertisol, alfisol, entisol, mollisol and aridisol groups of soils. In addition to DCPD, FePO₄ · 2H₂O (metastrengite) and AlPO₄ · 2H₂ O-monoclinic (metavariscite) were formed in alfisol and oxisol soils with ANP of 30 and 50 per cent WSP. FePO₄ · 2H₂O and AlPO₄ · 2H₂O (metavariscite) were identified in alfisol and oxisol soils while AlPO₄ · 2H₂O-orthorhombic (variscite) was formed in alfisol soils with ANP of 70 per cent WSP.     

Condensed combustion products of aluminized propellants. IV. Effect of the nature of nitramines on aluminum agglomeration and combustion efficiency

The condensed combustion products of two model propellants consisting of ammonium perchlorate, aluminum, nitramine, and an energetic binder were studied by a sampling method. One of the propellants contained HMX with a particle size D ₁₀ ≈ 490 μm, and the other RDX with a particle size _{D 10} ≈ 380 μm. The particle-size distribution and the content of metallic aluminum in particles of condensed combustion products with a particle size of 1.2 μm to the maximum particle size in the pressure range of 0.1–6.5 MPa were determined with variation in the particle quenching distance from the burning surface to 100 mm. For agglomerates, dependences of the incompleteness of aluminum combustion on the residence time in the propellant flame were obtained. The RDX-based propellant is characterized by more severe agglomeration than the HMX-based propellant — the agglomerate size and mass are larger and the aluminum burnout proceeds more slowly. The ratio of the mass of the oxide accumulated on the agglomerates to the total mass of the oxide formed is determined. The agglomerate size is shown to be the main physical factor that governs the accumulation of the oxide on the burning agglomerate. __________ Translated from Fizika Goreniya i Vzryva, Vol. 42, No. 4, pp. 78–92, July–August, 2006.     

Direct Ink-Jet Printing of Vertical Walls

Direct jet printing can assemble ceramic powder into a three dimensional shape by firing droplets of ink through a nozzle to build a multiple layered structure. As with stereolithography and selective laser sintering, the surface texture is expected to witness the layered assembly. The ability to create vertical walls by direct ink-jet printing was explored using a test piece based on a maze. The structure and topography are discussed in terms of droplet spreading and drying.     

对中国入世后洗涤剂工业形势及相关问题的分析 --国内外业界高层人士访谈

中国加入WTO后，中国洗涤用品行业面临着新的机遇与挑战，中国洗涤用品市场将面临更加激烈的竞争。由于环保的呼声越来越高，中国已开始在部分地区禁磷。中国洗涤用品工业将如何发展，其前景如何，专家的看法又如何，就这些问题本刊专访了有关人士。