珠光体球化的分形研究

珠光体球化反映到金相上，是一种不规则图像的变化，并且具有分形的特征，可望用分形几何的方法来进行描述。以Cr-Mo钢的珠光体球化为例，用分形维数来描述珠光体球化程度；用小岛法对15CrMo钢的珠光体球化图谱进行了测量。实验表明，珠光体球化从1级到6级，其相应的分形维数范围为1.3156-1.9282。从电厂运行了10^5h的15CrMo钢管上取样，实测了该试样的珠光体球化等级，结果表明，以分形维数表示的球化程度与按图谱评定的球化等级完全吻合。     

Fe3O4/PSt/TiO2多层包覆电磁响应微球的制备

首先采用分散聚合法将自制的Fe3O4磁流体和苯乙烯反应合成有磁核的Fe3O4/PSt磁性聚合物微球，然后，用非均匀成核水解反应在Fe3O4/PSt微球外包覆无定形二氧化钛，获得Fe3O4/PSt/TiO2复合微粒。用红外光谱、扫描电镜和热分析对粒子的形貌和结构进行了表征。并测试了微粒的介电性能和磁性，结果表明，所制得复合微粒有良好的电、磁响应性。     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

On the determination of optimal transition profile of a stepped bar in tension or in torsion by BEM

The objective is to have uniformly distributed tangential stresses on the transition profile of a stepped bar subjected to tensile and torsional loading using an axisymmetric boundary element formulation. The transition curve is represented by the Langragian interpolation polynomial with progressive degrees to avoid shape distortion during the optimization procedure. The calculated result is compared with that obtained by fluid dynamics given in the literature. It is seen that the transition curve obtained in this paper is reasonable.     

生物包粒的分类与命名——兼论徐州大北望中下寒武统生物包粒特征

对于碳酸盐岩中由生物及生物化学作用形成的具有同心或放射结构的异化颗粒(生物包粒),已为人们所熟悉,但目前还没有统一的分类与命名。本文在研究徐州大北望中下寒武统生物包粒特征的基础上,结合已有研究成果,对由生物及生物化学作用形成的具有同心或放射状内部结构的碳酸盐颗粒,按其粒度和形成颗粒的生物类型不同进行分类命名,提出分类命名的原则。     

浅谈无缝钢管的壁厚偏差

通过探讨、分析无缝钢管壁厚偏差产生的原因，提出了改善钢管壁厚偏差的一些措施，并结合实际生产，得出了比较满意的结果。     

18Ni（350）马氏体时效钢的磁滞特性

采用双时效处理工艺研究了热轧１８Ｎｉ（３５０）马氏体时效钢的磁滞特性。结果表明，８２０℃·　ｈＡＣ＋（５９－６１０）·。ｈＡＣ＋５１０℃·。ｈＡＣ和８２０℃·　ｈＡＣ＋（６９０－７１０℃）·３ｈＡＣ＋１５０℃·３ｈＡＣ处理具有较高的磁滞性能，在对大量数据进行二元线性回归的基础上得出了１８Ｎｉ（３５０）马氏体时效钢磁滞特性的分段关系式。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

低温腐蚀及其防护技术

为了加热炉和锅炉的安全经济运行 ,分析了烟气余热回收中低温腐蚀的机理 ,提出了行之有效地解决和防止低温腐蚀的几种技术方法