放电等离子烧结工艺对Ca3Co4O9陶瓷织构及电性能的影响

采用溶胶-凝胶与放电等离子烧结(SPS)相结合的方法制备了Ca3Co4O9陶瓷.通过X射线衍射、扫描电镜等表征手段,研究了放电等离子烧结工艺对Ca3Co4O9物相、显微结构和性能的影响.实验结果表明片状颗粒和放电等离子烧结工艺,特别是烧结温度的提高有利于Ca3Co4O9织构的形成.初步认为是片状颗粒在脉冲电流所产生的脉冲磁场作用下发生重排,使颗粒定向排列.本实验范围内,当烧结温度从700℃提高到900℃时,Ca3Co4O9晶粒取向度从0.75增大到0.87,700℃下的电阻率从6.24×10-5 Ωm降低到5.59×10-5 Ωm.此外,Ca3Co4O9块体表现出典型的半导体电学特征,电导率随着SPS烧结温度和测量温度的升高而增大,当SPS烧结温度为850℃时,P型Ca3Co4O9化合物在700℃有最大电导率.     

循环应力幅和平均应力对Ni3Al（B）合金高温疲劳寿命的影响

本文研究了高温下呈现脆性的多晶Ｎｉ３Ａｌ（０．６ａｔ－％Ｂ）合金的高温疲劳性能。载荷控制的拉－拉疲实验在４５０℃及空气条件下完成，通过固定所有实验中最大拉伸应力值，而改变不同实验中最小拉伸应力值的方法，可区分循环应力幅或平均应力及其交互作用的对材料影响，本实验获得的循环应力幅度及平均应力与环境的寿命的关系曲线呈现“Ｓ”形。本文初步分析了上述实验现象。     

弥散强化铜基复合材料钎焊接头强度

从冶金方面就如何改善Al2O3P颗粒与钎缝的化学相容性及工艺参数对钎焊接头力学性能的影响进行了初步探讨。研究结果表明。当保温时间较短时，由于钎缝中含有较多的Al2O3P颗粒相，且有偏聚的趋势，钎焊接头强度较低；延长保温时间，钎料中活性组元Ti与Al2O3P颗粒反应，可以有效控制Al2O3P含量，从而减缓其不利影响，使钎焊接头强度大幅度提高。     

机械合金化过程中Fe75 Al25二元系统的结构演变

采用X射线衍射仪、差式扫描量热仪等研究机械合金化过程中Fe75Al25元素混合粉的结构演变及热处理对粉体结构的影响。研究表明：球磨过程中，Al向Fe中扩散，直至Al完全溶入Fe中形成非平衡过饱和固溶体Fe(Al)。球磨过程中，Fe75Al25元素混合粉晶粒细化呈现先快后慢的趋势，球磨25h后的晶粒尺寸为6．9nm。Fe75Al25元素混合粉在球磨后的热处理过程中，由无序的Fe(A1)固溶体向有序的DO3-Fe3Al金属间化合物转变。     

Resistance of Mo-bearing stainless steels and Mo-bearing stainless-steel coating to naphthenic acid corrosion and erosion-corrosion

Naphthenic acid corrosion (NAC) and erosion-corrosion (NAEC) behavior of Mo-bearing (0-7.0 wt.%) stainless steels have been investigated in laboratory to evaluate the essential role of Mo on their NAC and NAEC resistance. The NAC and NAEC resistance of a high-velocity-oxygen-fuel (HVOF) thermal sprayed Mo-bearing stainless-steel coating was also investigated in both laboratory and an oil refinery. It was found that increasing the Mo content remarkably enhanced the NAC and NAEC resistance of stainless steels. The Mo-rich areas or phases in the steels played an importance role in resisting the NAEC. The HVOF coating showed excellent NAC and NAEC resistance in laboratory tests. The 700-day field test in an oil refinery revealed that the coating can effectively prevent the carbon-steel substrate from erosion-corrosion during long-term exposure in oil-refining environment. The corresponding NAC and NAEC mechanisms of the stainless steels and the beneficial role of Mo were discussed by taking account of inherent susceptibility of metal elements to corrosion, possible effects of Mo on surface films, and Mo-induced change in microstructure and microhardness.     

内氧化法制备Al2O3/Cu复合材料的研究现状

综述了内氧化法制备Al2O3／Cu复合材料的研究现状，总结了内氧化法制备Al2O3／Cu复合材料的必备条件，对内氧化动力学和热力学进行了详细的阐述，并以Cu2O为氧源，采用内氧化法制备了Al2O3／Cu复合材料，验证了其优越的室温和高温性能；对以复合材料棒材为原料制备的点焊电极进行装机试验，结果表明其寿命为传统Cu-Cr—Zr电极的3～5倍；最后着重分析了内氧化法制备Al2O3／Cu复合材料发展过程中亟待解决的问题。     

微量稀土Er对Al-5Mg合金组织与性能的影响

采用铸锭冶金法,制备含不同量稀土元素Er的Al-5Mg合金。利用拉伸力学性能测试、OM、XRD、SEM、TEM及EDS分析等分析测试手段,研究微量Er对Al-5Mg合金微观组织与力学性能的影响。结果表明:Er可以明显提高Al-5Mg合金的强度,添加0.4%Er(质量分数)的Al-5Mg合金的冷轧态屈服强度(σ0.2)提高了81MPa,而延伸率变化不大;Er的加入还能减少Al-5Mg合金的枝晶偏析,并可显著细化合金的晶粒组织;Er对晶粒的细化机理与其添加量有关,当Er含量较低时,符合传统的稀土细化机理;当Er含量较高时,由于在熔体中形成了初生Al3Er质点,在结晶形核时可以作为非均质形核核心,从而可显著细化晶粒组织;Er对合金的强化效应主要来自于晶粒细化及在晶内形成的细小二次Al3Er质点。根据实验结果可知,添加0.4%Er可使合金具有较为优异的综合性能。     

内氧化制备Cu/Al2O3弥散强化铜的组织性能研究

实验用Cu2O粉作氧化剂,采用简化的内氧化法工艺,在900℃下使Cu-Al合金薄平板内氧化,获得Cu/Al2O3复合材料。研究不同氧化时间(3、6、10 h)下的Cu/Al2O3复合材料的组织特征及性能。研究表明:复合层中Al2O3颗粒呈弥散状分布;复合层表面和内部的晶粒大小明显不同,由于表面Al2O3析出较早,阻止晶粒的充分长大;表面晶粒较小,表面硬度随时间延长而升高。     

Development of Si3Na/Al composite by pressureless melt infiltration

Pressureless infiltration process to synthesize Si3N4/Al composite was investigated. Al-2%Mg alloy was infiltrated into Si3N4 and Si3N4 containing 10% Al2O3 preforms in the atmosphere of nitrogen. It is possible to infiltrate Al-2%Mg alloy in Si3N4 and Si3N4 containing 10% Al2O3 preforms. The growth of the dense composite of useful thickness was facilitated by the presence of magnesium powder at the interface and by flowing nitrogen. During infiltration Si3N4 reacted with aluminium to form Si and AIN, the growth of composite was found to proceed in two ways, depending on the Al2O3 content in the initial preform. Firstly, preform without Al2O3 content gives rise to AIN, Al3.27Si0.47 and Al type phases after infiltration. Secondly, perform with 10% Al2O3 content gives rise to AIN-Al2O3 solid solution phase （AION）, MgAl2O4, Al and Si type phases. AlON phase was only present in composite, containing 10% Al2O3 in the Si3N4 preforms before infiltration.     

A novel grating matching method for 3D reconstruction

Automatic 3D surface reconstruction has been an important research topic in digital photogrammetry for many years. Shaping from stereoscopic information is one of the widely studied topics in computer vision. Its central part is to solve the stereo matching problem automatically. Most algorithms used to solve the matching problem can be categorized as either area-base techniques or feature-based techniques. Feature-based techniques have gained more and more popularity for and it is the method that supports activities in object recognition and image understanding. But none of the former research can ensure the 100% matching exactness, thus, cannot complete high precision 3D surface measurement. In order to improve the precision of 3D measurement, we design a novel grating matching method, which can ensure 100% matching accuracy. It does not need any other assistant symbol or flag, only select one of the gratings which have to be projected to the objects. On the beginning of the measurement, the background of the object is captured by a CCD camera. Later gratings include single grating and group gratings will be projected to the object in sequence. All the images include gratings will make a subtraction with the background. The difference of the two images will be treated as 3D cues to acquire the 3D shape. Because no recognizing work is needed, the location of the single grating and each one in the group can be positioned exactly. From a lot of experiments, the proposed grating matching method is proved and it is a technique with high precision, low costs, easy operation, and an automatically matching method. Furthermore, it can be widely used in most of 3D vision recovery systems.