泡沫铝的动态压缩性能和吸能性研究

通过测量泡沫铝在动态和准静态压缩条件下的应力 -应变曲线 ,研究了泡沫铝的准静态和动态压缩行为以及不同应变条件下的吸能性 ,并对其应变率效应进行了分析。结果表明 ,在高应变速率和准静态压缩下 ,泡沫铝的σ -ε曲线均表现出弹性变形段、平缓段和密实段三阶段特征 ;泡沫铝的压缩性能具有明显的应变速率敏感性 ,随应变速率的提高 ,流动应力上升 ,吸能性升高     

镁合金表面喷铝防腐蚀层的微观组织分析

在AZ91D镁合金表面热喷铝，用以提高其表面的耐腐蚀性能。采用SEM，EPMA等方法对AZ91D表面喷铝扩散层的组织进行了仔细的观察与分析，发现在防腐蚀层上有大量的Mg17Al12相存在，且呈决状及非连续片状分布。经显微硬度测定，喷铝层硬度较镁合金基体高；腐蚀后这种相凸出于基体，比镁合金基体有较好的耐腐蚀性能。     

表面引发剂对熔融铝合金直接氧化生长的影响

为了控制熔融铝合金直接氧化法制备Al2O3/Al复合材料的氧化生长,采用ZnO,SiO2和MgO3种表面引发剂,研究它们对Al-Si-Zn合金氧化生长过程及Al2O3/Al复合材料组织形貌的影响.结果表明:与未使用引发剂时相比,使用SiO2,ZnO或MgO表面引发剂制备的粉末都能显著地缩短Al-Si-Zn合金的氧化生长孕育期,提高合金氧化生长速率,改善复合材料的胞状生长方式,提高复合材料的组织均匀度和致密度,为实际生产应用提供了依据.实验发现:ZnO表面引发剂的使用效果最为突出,其最佳添加量为12mg/cm2.     

大型预焙铝电解槽使用碳化硅砖与普通碳砖复合块的探讨

碳化硅砖和碳化硅砖与普通碳砖复合侧块，在上世纪末期我国铝电解槽上开始推广应用。使用后各厂家普遍发现碳化硅砖及碳化硅砖与普通碳块复合侧块均出现不同程度的断裂、上抬和脱落现象，该文对断裂、上抬和脱落原因进行了分析，并提出了改进措施。     

Corrosion Behavior of a Sputtered K38G Nanocrystalline Coating with a Solid NaCl Deposit in Wet Oxygen at 600 to 700°C

A nanocrystalline coating of K38G alloy was obtained by means of magnetron sputtering. The corrosion behavior of cast K38G alloy and its sputtered nanocrystalline coating with a solid NaCl deposit in dry air or wet oxygen at 600 and 700°C have been studied and compared. The results indicated that the mass gain of the coating is higher than that of the cast alloy at 600 and 700°C. Therefore, nanocrystallization reduced the corrosion resistance at these temperatures. Furthermore, the mass gains of the coating and the cast alloy with a NaCl deposit in wet oxygen were less than that with a NaCl deposit in dry air. The relevant corrosion mechanisms are discussed.     

蒸馏与减粘热联合装置的设备腐蚀及防护

介绍了锦西石化分公司南蒸馏与减粘热联合装置炼制辽河高酸值原油及带炼高硫进口油在 2 0 0～40 0℃范围内对设备、管线和阀门的腐蚀特点、腐蚀机理以及针对高温环烷酸腐蚀所采取的防护措施。通过试验和理论分析 ,提出了应用新材料和新工艺解决减粘后高温渣油系统的腐蚀及低温露点腐蚀的建议     

非化学计量LaNi5型储氢合金的性能

采用富La混合稀土与Ni、Co、Mg等元素组合，获得了一种非化学计量LaNi5型储氢合金、用金相、XRD和SEM-EDX等方法分析了该合金的组织结构，研究了合金的气相储氢特性以及电化学性能，结果表明：在1.6MPa氢压和温度29℃下，该合金的储氢量达到1.58%（质量分数），该合金的放电容量为380mAh/g。经300次循环后容量保持率为55%，该合金的基体是CaCu5型结构的LaNi5相，但有第二相（LaMg)Ni3析出，这种第二相的形成是导致该合金大容量的关键。     

表面电沉积合金层提高碳钢齿轮的接触疲劳强度研究

 接触疲劳破坏是齿轮的主要失效形式之一． 在45#钢齿轮齿面电沉积Ni-P-Co合金层，可以显著提高其接触疲劳强度．同时，对合金层的表面形貌，表面粗糙度、显微硬度和疲劳点蚀坑形貌特征等进行了分析．     

REHEATING TEMPERATURE CONTRAST AND MICROSTRUCTURES OF 7075 Al ALLOY CAST BY LIQUIDUS SEMI-CONTINUOUS CASTING

In this study, reheating of liquidus semi-continuous cast billets of 7075 Al alloy was carried out in a resistance furnace, and the temperature contrast of the outer and the center of the reheated billets was investigated, then the reheating microstructures were investigated. Results show that: the difference of temperature between the outer and center is small and the difference of their microstructures are also small. During reheating at 576℃ the spheroidization of grains is significant after 5min and no rosettes are visible after 20min by optical microscopy. Similar observations were madeon materials reheated at 596℃, but the ripening process is faster. The grains growup to 30-60μm, fine enough for thixoforming.