参数设计法在铝电解电容器设计中的应用探讨

论述了参数设计法在铝电解电容器设计开发阶段的应用。文中阐明了铝电解电容器的主要质量特性(损耗因子、电容量)及芯包外径的参数设计原理,并建立了归一化函数作为优选设计方案的判据。实例证明在铝电解电容器的设计过程中应用参数设计法以减小产品质量特性变异是有效的。     

Failure of a stationary pump engine piston

Piston failures are not a common occurrence, but they do occur, and failure is usually associated with fatigue crack growth. Most failures initiate at the gudgeon pin hole or in the skirt of the piston. Occasionally they fail elsewhere. In the example covered in this paper, failure initiated in the crown and progressed down to the gudgeon pin before final failure occurred. This paper outlines the cause and mode of failure and shows that small metallurgical discontinuities can contribute to these failures under the right circumstances.     

铝型材推弯工艺

通过铝型材圆环的推弯实验,研究了推弯工艺原理、变形过程,结合有限元模拟得到了和实验结果相吻合的型材厚度分布、成形零件卸载回弹后的曲率半径及型材截面畸变.结果表明:推弯零件曲率及截面畸变一致性高,成形模具结构简单且便于调整,数值模拟可以用于推弯工艺的优化分析.     

Effect of heat treatments on tensile properties and microstructures of wrought Mg−Zn−Zr-RE alloys

The effect of heat treatments on the tensile properties and microstructures of wrought Mg–Zn–Zr-Rare earth alloys MB25 and MB26 have been studied in this paper. It was shown that the homogenization of the cast ingots decreased the strength of the extruded bars because some grain boundary phases were dissolved during the process of this treatment, while the ageing treatment of the extruded bars increased the strength due to the dispersive precipitation of MgZn₂ phase. The quenching + ageing treatments of the extruded bars decreases the strength and plasticity because of the growing up of the grains.Abbreviations ED electron diffraction - GB grain boundary - RE rare earth - TEM transmission electron microscope     

Structure of rapidly solidified aluminum alloys

This paper is a summary of an extensive research program carried out by the authors on the structure of rapidly solidified aluminum alloys; and a comparison with the work of others also involved in this field. The paper discusses the changes in the dendritic and non-dendritic structure of the matrix at cooling rates from 10^–3 to 10¹⁰ K/s and discusses the hetergeneity of the structure caused by interdendritic-segretion during solidification.     

含钡合金在钢液中的脱氧行为研究

在MoSi2炉上采用MgO质坩蜗对钢管进行了含钡合金脱氧行为的研究。实验中钡系合金主要选取SiAUBa、SiCaBa、SiAlBaCa、SiAlBeCaSr及用于钙处理的SiCa包芯线，选用Al作为对比脱氧剂，考察了钡系合金脱氧的全氧含量，脱氧产物的分布、尺寸和形貌，探讨了钡系合金脱氧和对夹杂物变性作用的机理。     

Preparation of Ultra—fine Aluminum Nitride in Thermal Plasma

Ultra-fine aluminum nitride has been synthesized by the evaporation of aluminum powder at atmospheric-pressure nitrogen plasma in a hot-wall reactor.The average size of aluminum nitride particle is 0.11μm measured by scanning electric mirror(SEM),and the purity is at least over90% evaluated by X-Ray diffraction(XRD).The conversion of Al powder to aluminum nitride is strongly depended on the injection of NH3.Typical experimental parameters such as the feed rate of raw material,the flow rate of ammonia and the position of injecting aluminum powder into the reactor are given.     

P／MCs新型复合材料制备、结构及阻尼性能

采用特殊的渗流法所制备的新型Ｐ／ＭＣｓ复合材料，由高分子聚合物与蜂窝状铝架组成，它具有优异的阻尼性能，并简述了结构对阻尼的影响     

过共晶Al－Si合金共生区激光表面处理

用２ｋＷ连续ＣＯ２激光对过共晶Ａｌ－１８Ｓｉ合金以不同能量密度和扫描速度进行快速熔凝处理。用扫描电镜、电子微区分析仪分析了微观结构。从计算机对Ａｌ－Ｓｉ合金ｆ－ｎｆ系统的非平衡理论计算所得的共生区及实验结果的分析可见，当能量密度和扫描速度决定的凝固条件处于共生区中部时，过共晶Ａｌ－Ｓｉ合金激光表面处理可以得到共晶间距低于２００ｎｍ的完全共晶结构。     

过共晶铝硅合金细化初晶硅的研究

研究了ZL8604过共晶铝硅合金初晶硅细化剂和加入方式与加入量以及影响细化效果的冶铸工艺因素,实验结果达到了技术指标要求。