Kinetics of light-induced degradation in compensated boron-doped silicon investigated using photoluminescence and numerical simulation

We use photoluminescence to observe light-induced degradation in silicon in real time. Numerical simulations are used to match our results and lifetime decay data from the literature with theoretical models for the generation of the light-induced boron–oxygen defects. It is found that the existing model of the slowly generated defect SRC, where its saturated concentration is a function of the majority carrier concentration, does not explain certain results in both p- and n-type samples. A new model is proposed in which the saturated SRC concentration is controlled by the total hole concentration under illumination.     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

Design of an antibacterial gelatin based on a covalent protein–protein coupling

An antibacterial peptide (AMP), i.e., nisin, was covalently bound to gelatin through a protein–protein coupling. Various reaction conditions were tested to study and optimize parameters of grafting e.g., orientation and density of AMP, which could impact the final antibacterial activity of the modified biopolymer. Modification was investigated by Fourier transform infrared (FT‐IR) spectroscopy and zeta potential. The antibacterial activity of the nisin‐enriched gelatin was evaluated against two staphylococci bacterial strains, i.e., Staphylococus epidermidis and Staphylococcus aureus. A higher activity was found for gelatin modified at pH = 7.4 revealing an influence of the nisin orientation on the protein antibacterial property. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41825.     

Alloying behavior and novel properties of CoCrFeNiMn high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

An equiatomic CoCrFeNiMn high-entropy alloy was synthesized by mechanical alloying (MA) and spark plasma sintering (SPS). During MA, a solid solution with refined microstructure of 10 nm which consists of a FCC phase and a BCC phase was formed. After SPS consolidation, only one FCC phase can be detected in the HEA bulks. The as-sintered bulks exhibit high compressive strength of 1987 MPa. An interesting magnetic transition associated with the structure coarsening and phase transformation was observed during SPS process.     

Modelling dislocation assisted tempering during rolling contact fatigue in bearing steels

Rolling contact fatigue in bearing steels is manifested by dark-etching regions, which are attributed to deformation induced tempering. In order to quantitatively explain this phenomenon, a model is suggested for martensite tempering assisted by dislocation glide during rolling contact fatigue. In the model, dislocations transport carbon from the matrix to carbide particles, provided that the carbon is located at a certain distance range from the dislocation contributing to the tempering process. By calculating the amount of carbon in the matrix, the kinetics of carbide thickening and hardness reduction are computed. It is found that the dark-etching region kinetics can be controlled by both bearing operation conditions (temperature and deformation rate) and microstructure (type, size, and volume fraction of carbides). The model is validated against tested bearings, and its limitations are discussed.     

Nonlinear viscoelastic modeling of soft polymers

A one‐dimensional phenomenological constitutive model, representing the nonlinear viscoelastic behavior of polymers is developed in this study. The proposed model is based on a modification of the well‐known three element standard solid model. The linear dashpot is replaced by an Eyring type one, while the nonlinearity is enhanced by a nonlinear, strain dependent spring constant. The new constitutive model was proved to be capable of capturing the main aspects of nonlinear viscoelastic response, namely, monotonic and cyclic loading, creep and stress relaxation, with the same parameter values. Model validation was tested on the experimental results at various modes of deformation for two elastomeric type materials, performed elsewhere. A very good agreement between model simulations and experimental data was obtained in all cases. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42141.     

Bi2O3–Nd2O3–WO3 system: Phase formation,polymorphism, and conductivity

Cubic, tetragonal, and monoclinic (Bi₂O₃)_x (Nd₂O₃)_y (WO₃)_z (x + y + z = 1) solid solutions based on the Bi₂O₃ oxygen ion conductor have been prepared by solid-state reactions in the ternary system Bi₂O₃–Nd₂O₃–WO₃. The field of monoclinic compounds with a Bi_3·24La₂W_0·76O_10.14-type structure has been shown to account for most of the ternary system. Compounds with a cubic fluorite structure exist at the boundary of the monoclinic phase field in two small regions at high (83–91 mol% Bi₂O₃, δ-phase) and low (20–55 mol% Bi₂O₃, δ′-phase) Bi concentrations. The cubic samples of the δ-phase retain their structure only during rapid heating and cooling, but annealing in the range of 300–700 °C results in structure degradation to lower symmetry phases. The monoclinic compounds and Bi-poor cubic compounds (δ′-phase) have good thermal stability. The cubic samples of the δ′-phase are hygroscopic. Their bulk conductivity noticeably increases with atmospheric humidity, suggesting that these materials are potential proton conductors.     

Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

移动边缘计算环境下的动态资源分配策略

在通讯设备爆炸式增长的时代,移动边缘计算作为5G通讯技术的核心技术之一,对其进行合理的资源分配显得尤为重要。移动边缘计算的思想是把云计算中心下沉到基站部署(边缘云),使云计算中心更加靠近用户,以快速解决计算资源分配问题。但是,相对于大型的云计算中心,边缘云的计算资源有限,传统的虚拟机分配方式不足以灵活应对边缘云的计算资源分配问题。为解决此问题,提出一种根据用户综合需求变化的动态计算资源和频谱分配算法(DRFAA),采用"分治"策略,并将资源模拟成"流体"资源进行分配,以寻求较大的吞吐量和较低的传输时延。实验仿真结果显示,动态计算资源和频谱分配算法可以有效地降低用户与边缘云之间的传输时延,也可以提高边缘云的吞吐量。     

Epos – an instrument for the assessment of the ethical position in software development

Digital technology becomes more powerful, intelligent, pervasive and ubiquitous. Ethical aspects of this development have not yet drawn the appropriate attention of researchers and engineers. This paper presents an instrument that aims at measuring the individual ethical position with regard to the design and development of computer software. The development of the Epos tool was based on two data collections. The data of the first survey (n₁ = 147 participants) were used to select items and to determine the factorial structure of the questionnaire. Results show that the Epos instrument reliably assesses peoples’ ethical opinion with respect to five central components: (1) regulation, (2) data privacy, (3) domain specific knowledge, (4) societal responsibility and (5) company responsibility. In the second survey, we determined the stability of the instruments factor structure by assessing a sample of n₂?=?196 participants. A confirmatory factor analysis (CFA) supported the initial factor structure. Next steps and further implications are discussed regarding the final version of the questionnaire.