半固态ZnAl 27合金及其二次加热组织

研究了半固态ZnAl27合金及其二次加热组织。结果表明，半固态ZnAl27合金基本无宏观偏析，其组织为细小均匀的近球形非枝晶，综合力学性能远远高于常规铸造合金；二次加热后，α相进一步球化，边缘变得光滑圆整，可以满足半固态触变成形的需要。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

Electrical and growth characteristics of Au/Al0.15Ga0.85N:Si structures with various Si incorporations

We have investigated the growth characteristics of n-Al_0.15Ga_0.85N:Si/GaN and the electronic properties of Au/n-Al_0.15Ga_0.85N:Si diode structures grown by metal-organic chemical vapor deposition (MOCVD) with various Si incorporations. The Al_0.15Ga_0.85N:Si layers were grown on undoped GaN/sapphire (0001) epitaxial layers in a horizontal MOCVD reactor at the reduced pressure of 300 torr. The mirrorlike surface, free of defects, such as cracks or hillocks, can be seen in the undoped Al_0.15Ga_0.85N epilayer, which was grown without any intentional flow of SiH₄. However, many cracks are observed in the n-Al_0.15Ga_0.85N:Si, which was grown with Si incorporation above 1.0 nmol/min. While Au/n-Al_0.15Ga_0.85N:Si diodes having low incorporation of Si showed retively good rectifying behavior, the samples having high Si incorporation exhibited leaky current-voltage (I-V) behavior. Particularly, the Au/n-Al_0.15Ga_0.85N:Si structure grown with Si incorporation above 1.0 nmol/min cannot be used for electrical rectification. Both added tunneling components and thermionic emission influence the current transport at the Au/n-Al_0.15Ga_0.85N:Si barrier when Si incorporation becomes higher.     

开关稳压电源用铝电解电容器的失效机理

概述了开关稳压电源用铝电解电容器的工作状态和失效模式，着重讨论了开关稳压电源用铝电解电容器的开路失效和击穿失效机理。     

2Mbit/s高速信令链路在移动通信七号信令网中的应用

通过对2Mbit/s高速信令链路原理、特点的介绍，阐明了该技术在现阶段使用的实际意义，并给出了2Mbit/s高速信令链路在移动通信七号信令网中的应用。     

化学镀非晶态Ni—B合金的研究

本文通过化学镀方法在铜和钢上沉积非晶态Ni-B合金。着重讨论了还原剂浓度、络合剂浓度对化学镀沉积速率的影响;分析了它的耐蚀原因和其显微硬度随退火温度的变化情况并就其应用和发展略作说明。     

5754-H34铝合金板材生产工艺研究

研究了不同冷变形程度，退火温度对5754铝合金冷轧板材的组织和力学性能的影响，确定了5754合金H34状态板材的生产工艺参数，即冷变形程度25%-45￥，稳定化退火温度120-160℃，保温时间3-6h，在工业生产条件下，其产品的技术指标达到了用户要求。     

改性石英砂滤料强化过滤处理含藻水

采用改性石英硝滤料强化过滤处理含藻水的试验结果表明，与石英硝滤料相比，改性石英硝滤料对含藻水具有优良的处理效果；经混凝沉演后水中的余铝对藻类的去除有促进作用。     

钨合金圆筒爆破试验破片分布的统计分析

采用圆筒爆破试验方法研究了易碎型钨合金的破片分布特征,并与93W合金的结果进行了对比.对破片的数量和质量分布特征进行了统计分析,发现易碎型钨合金的破片率明显高于93W合金,而且破片的均匀性也明显好于93W合金,但易碎钨合金的破片回收率低于93W合金,而且受装药量的影响较大.     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.