纤维混凝土在水工建筑工程中的应用(上)

概述改性混凝土垢发展情况，介绍纤维混凝土在国内外水工建筑物上的应用实例，提出钢纤维增强钢筋混凝土水工建筑结构强度计算方法。包括受弯构件正截面强度，斜截面抗剪强度的计算；重点介绍了网状钢纤维增强混凝土（FOC）在水工建筑物上的应用，包括在渡槽，闸门，小型拦河坝，轻型岸型等工程上的应用实例，T新梁正斜截面的强度计算，板材承载力计算的方法。     

影响掺矿渣的钢纤维砼强度的主要因素

研究结果表明 :水胶比、胶凝材料用量、钢纤维掺量、矿渣代水泥量对钢纤维砼强度影响显著。当矿渣取代水泥 10 %时 ,钢纤维砼强度最高。经试验选择出一个具有良好和易性和较高强度 (118MPa)的钢纤维砼配合比 ,为掺磨细矿渣的中含量超短异形钢纤维砼的设计和施工提供了试验依据     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

钢纤维喷射混凝土作为面板材料的可行性研究

钢纤维混凝土作为一种新型增强材料，以其较好的受力变形特性在水利水电，交通，海岸防护，港口及军事等诸多工程中得到了广泛的应用。针对混凝土面板堆石坝面板的受力变形特点，为改善水布垭面板堆石坝面板的受力条件，提高其防渗能力，同时方便施工，现提出采用钢纤维喷射混凝土作为水布垭面板堆石坝面板材料的新构想，并通过对钢纤维喷射混凝土的物理力学特性及堆石坝面板受力变形进行分析，为钢纤维喷射混凝土在水布垭面板堆石坝面板中的实际应用提出了建议方案。     

Failure analysis used for remanufacturing of steel rolling components

The guide-pieces, used in the process line of steel rolling, were the important components. The guidepieces, which were slide contacting with the rolled-piece, had a high temperature and high speed. The wear was very serious. The results from failure analysis showed that there were three failure forms in the guide-pieces: the first was the wear during heat friction, the second was the heat fatigue under the cycle of deep heating and deep cooling, and the third was the impact rupture. Among them, the wear was the main reason. To the wear of guidepieces, there were four mechanisms, namely abrasive wear, adhesive wear, fatigue wear and corrosion wear. The failure analysis to the guide-piece laid the foundation for its remanufacturing. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China     

轻型钢骨结构低层住宅设计荷载分析

本文讨论了北美低层钢骨结构住宅结构设计的荷载问题，包括各类荷载的取值和计算方法，以及荷载组合模式，并提出了在我国相关规范没有出台前，在国内进行设计时应该注意的一些问题。     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

Finite‐Element Implementation of a Self‐consistent Texture Model with a Hardening Law Based on Dislocation Densities

A self‐consistent texture model is implemented in the finite‐element code ABAQUS/Explicit®. Hardening of the slip systems is described by evolution laws for dislocation densities, and the Bauschinger effect is included. With these ingredients the cold rolling of an IF‐steel is simulated and the evolution of texture and anisotropy is examined. The use of the dislocation based hardening law is found to have a significant effect on the evolution of the anisotropic yield surface, but only very little influence on the texture. Furthermore, the hardening model is used to investigate the evolution of dislocation densities in differently oriented grains during plane strain compression. It is found that the dislocation density varies greatly depending on orientation, an observation which can help to explain the orientation dependence of recrystallization.     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.