双波长稳频CO_2激光模糊控制系统的建模与优化

报导一种模糊逻辑控制系统的建模与优化方法。以此方法设计的模糊逻辑控制器，用于双波长稳频ＣＯ２激光器的控制得到令人满意的结果。     

微机监控技术 一

本文系统地讲述了以微型计算机为中心的微机监控系统的工作原理、系统组成和应用方面的有关技术。分为监控系统的功能和结构、硬件系统和软件系统三个部分。本文为第一部分。     

基于信息的智能控制理论研究

本文介绍的基于信息的智能控制理论的发展过程，主要分为智能控制的信息指标和智能控制的信息结构分析两部分，文中在最后对这套理论可能的发展方向进行了探讨。     

可移动机器人的运动学模型与控制原理

本文首先对可移动机器人的运动学进行了分析，建立了运动学模型与控制结构图，然后采用时域分析法对此系统进行了校正，最后通过对此系统的仿真与时测实验，对各校正环节的参数进行了整定。     

大系统分散鲁棒容错控制的进展及主要成果

综述了近２０年来关联大系统分散鲁棒容错控制的研究动态及取得的主要成果。说明了统一地研究分散鲁棒容错控制的必要性。在分散控制、鲁棒控制和容错控制研究领域内，分析了各种设计方法的主导思想及实质；指出了这些研究成果的意义与存在的问题。文中着重论述了分散、鲁棒、容错控制研究方法的发展途径。     

给水流量控制系统仿真辅助设计

本文将给水流量系统规范化，给出静、动态数学模型，通过计算机仿真计算建立起设计参数Ｓ与系统特性间关系数据库，这些数据可用于控制系统辅助设计。本文还介绍了在Ｓ较小时自动补偿系统增益和时间常数的自适应控制方法并给出仿真结果。     

A delta transform approach to loop gain-phase shaping design of robust digital control systems

This paper addresses the existence of loop gain-phase shaping (LGPS) solutions for the design of robust digital control systems for SISO, minimum-phase, continuous-time processes with parametric uncertainty. We develop the frequency response properties of LGPS for discrete-time systems using the Δ-transform, a transform method that applies to both continuous-time and discrete-time systems. A theorem is presented which demonstrates that for reasonable specifications there always exists a sampling period such that the robust digital control problem has a solution. Finally, we offer a procedure for estimating the maximum feasible sampling period for LGPS solutions to robust digital control problems.     

Quantitative feedback theory with applications in welding

Two different control systems were developed using quantitative feedback theory for weld quality improvement. The first application to be discussed was designed for the resistance pinch welding process and uses electrode displacement and force as feedback parameters. A correlation between weld quality and electrode displacement is established for constant electrode force. The system is capable of producing repeatable welds of consistent quality, with wide variations in weld parameters. This is the first time feedback control has been successfully applied to pinch welding. The second example presented in this paper was developed for penetration control of the gas-tungsten-arc welding process. The feedback signal is obtained by measuring the amount of light emitted from the back side of the weld. Welds of constant penetration have been demonstrated in tests with travel speeds varying from 1.5 to 6 inches per minute and with 200 per cent changes in part thickness.     

Robust crossfeed design for hovering rotorcraft

Control law design for rotorcraft fly-by-wire systems normally attempts to decouple the angular responses using fixed-gain crossfeeds. This approach can lead to poor decoupling over the frequency range of pilot inputs and increase the load on the feedback loops. In order to improve the decoupling performance, dynamic crossfeeds should be adopted. Moreover, because of the large changes that occur in the aircraft dynamics due to small changes about the nominal design condition, especially for near-hovering flight, the crossfeed design must be ‘robust’. A new low-order matching method is presented here to design robust crossfeed compensators for multi-input, multi-output (MIMO) systems. The technique minimizes cross-coupling given an anticipated set of parameter variations for the range of flight conditions of concern. Results are presented in this paper of an analysis of the pitch/roll coupling of the UH-60 Black Hawk helicopter in near-hovering flight. A robust crossfeed is designed that shows significant improvement in decoupling perfomance and robustness over the fixed-gain or single point dynamic compensators. The design method and results are presented in an easily used graphical format that lends significant physical insight to the design procedure. This plant precompensation technique is an appropriate preliminary step to the design of robust feedback control laws for rotorcraft.     

Multi-input,multi-output flight control system design for the YF-16 using nonlinear QFT and pilot compensation

Nonlinear quantitative feedback theory (QFT) and pilot compensation techniques are used to design a 2 × 2 flight control system for the YF-16 aircraft over a large range of plant uncertainty. The design is based on numerical input-output time histories generated with a FORTRAN implemented nonlinear simulation of the YF-16. The first step of the design process is the generation of a set of equivalent linear time-invariant (LTI) plant models to represent the actual nonlinear plant. It has been proven that the solution to the equivalent plant problem is guaranteed to solve the original nonlinear problem. Standard QFT techniques are then used in the design synthesis based on the equivalent plant models. A detailed mathematical development of the method used to develop these equivalent LTI plant models is provided. After this inner-loop design, pilot compensation is developed to reduce the pilot's workload. This outer-loop design is also based on a set of equivalent LTI plant models. This is accomplished by modelling the pilot with parameters that result in good handling qualities ratings, and developing the necessary compensation to force the desired system responses.