苦味酸钾点火药在电点火头中的应用

通过理论分析和试验,从机械感度、燃烧精度、热安定性、性能、长贮等方面,对比分析了苦味酸钾点火药与DDNP点火药.结果表明:在电点火头制造中,采用苦味酸钾作为点火药的主要组分,具有热稳定性好、药头机械强度高、生产过程废品少、无环境污染等优点,尤其有利于提高电雷管的发火可靠性和一致性.     

Computer modeling of the continuous annealing furnace

A computer program to calculate the strip temperature heated in the continuous annealing furnace was developed, using the zone method for radiative heat transfer analysis with the measured gas temperature in the furnace. Using theF _E Operator, the present study considered the effects of soot and transient species, in addition to the H₂O−CO₂ gas mixture on the gas radiative heat transfer. The predicted strip temperature distribution forF _E=1.05 represented well the measured data. The maximum difference in the heat flux transfered to the strip from the combustion gas forF _E=1.0 (without soot and transient species gas radiation) and 1.05 (with soot and transient species gas radiation) was about 15%. The present study also investigated the effects of line speed and thickness variations on the strip temperature, establishing the bases for the on-line computer model.     

Insulating safety analysis of the hot-line sweeping robot

This paper presents a method of calculating the insulating safety distances for hot-line working robots at high voltage when dielectric is adulterated with conducts. Also, finite element method is adopted to calculate the electric field strength to find whether it is beyond the critical. The above methods have been applied to analyze the insulating safety of the robot for hot-line sweeping post insulators in a 220 KV substation. They have also been testified by experimentations.     

Design and evaluation of an active electromechanical wheel suspension system

This paper presents an electromechanical wheel suspension, where the upper arm of the suspension has been provided with an electric levelling and a damper actuator, both are allowed to work in a fully active mode. A control structure for the proposed suspension is described. The complex design task involving the control of the electric damper and its machine parameters is tackled by genetic optimisation. During this process, these parameters are optimised to keep the power dissipation of the electric damper as low as possible, while maintaining acceptable comfort and road-holding capabilities. The results of the evaluations carried out demonstrate that the proposed suspension can easily adopt its control parameters to obtain a better compromise of performance than that offered by passive suspensions. If the vehicle is to maintain acceptable performance during severe driving conditions, the damper has to be unrealistically large. However, if the electric damper is combined with a hydraulic damper, the size of the electric damper is significantly reduced. In addition, the design of the electric damper with the suggested control structure, including how it regenerates energy, is discussed.     

全封闭Ar气保护电渣重熔GH4169合金

上海五钢采用ALD 5t全封闭Ar气保护电渣重熔炉 ESR(Ar)冶炼了GH4 16 9合金锭 ,分析结果表明 ,ESR(Ar)电渣锭氧、硫含量和锭头尾碳、铝、钛之差远低于一般ESR工艺 ;VIM(真空感应熔炼 ) +ESR(Ar)工艺冶炼合金中平均氧含量 6× 10 - 6 远低于VIM +VAR(真空电弧重熔 )工艺冶炼合金中平均氧含量 13× 10 - 6 ,所以ESR(Ar)工艺脱氧效果优于VAR工艺     

钢包炉(LF)预熔精炼渣的研究

预熔精炼渣具有成分均匀，性能稳定，储存时不吸水等特点，钢包炉中使用预熔精炼渣时成渣均匀且速度快，具有较强的吸附钢中非金属夹杂的能力。综合脱硫率高等冶金效果。有显著净化钢液作用。     

柳钢混铁炉炉衬结构及运行管理的技改实践

针对混铁炉使用过程中出现的各种侵蚀状况，设计采用砖砌十浇注复合炉衬结构，特别对前墙拐角和后墙中段等侵蚀快的关键部位作了有针对性的技术改进；在运行管理上，制定推行全新的工艺操作规程，取得了显著的使用效果。     

Development of temperature compensated high elongation resistance strain gauges for use up to 250°C

The paper describes the development and evaluation of temperature compensated high elongation resistance strain gauges for use from room temperature to 250°C. These gauges could be temperature-compensated on steels with coefficient of thermal expansion α = 11 ppm/°C. Thermal output within 250°C was about 1 μm/m/°C and maximum standard deviation of 5 gauges was 34 μm/m. Strain limit was > 4% at room temperature and at 250°C. Gauge factors of different strain ranges at R.T. and at 250°C are tabulated. Some applications are stated.     

Characterization of CuInS2 thin films for solar cells prepared by spray pyrolysis

We have made a study of the chemical composition, the electrical, the optical and the structural properties of polycrystalline CuInS₂ thin films prepared by spray pyrolysis to be used for thin film solar cells. These films were deposited starting from aqueous solutions with different chemical compositions ([Cu]/[In] and [S]/[Cu] ratios) and at different substrate temperatures. In all cases, the material is p-type with grains preferentially oriented in the (112) direction of the sphalerite structure. The electro-optical properties show a very strong dependence on the [Cu]/[In] ratio in the solution. Films with copper excess have smaller resistivity and better crystallinity than those which are stoichiometric or have indium excess. The results obtained in this work show the possibility of having CuInS₂ thin films with a wide range of resistivity, a fact that could be important for making solar cells based on this material.     

剖析半悬挂减速机故障的产生与对策

介绍了半悬挂减速机的工作原理，分析其故障原因，实施相应的解决对策。