Effects of hot-carrier stress on high performance polycrystalline silicon thin film transistor with a single perpendicular grain boundary

This paper is a report on the effect of a single perpendicular grain boundary on the hot-carrier and high current stability in high performance polycrystalline silicon (poly-Si) thin film transistors (TFTs). Under a hot carrier stress condition (Vg = Vth + 1 V, Vd = 12 V), the poly-Si TFT with a single grain boundary is superior to the poly-Si without any grain boundary because of the smaller free carriers available for electric conduction. The shift of transconductance in poly-Si TFT with a single grain boundary is less than 5% after hot carrier stress during a period of 1000 s. The shift of transconductance is about 25% in the case of the poly-Si TFTs without a grain boundary in the channel. On high current stress, the poly-Si TFT without the grain boundary is less degraded than the poly-Si TFT with the grain boundary because the concentrated electric field near the drain junction is lower.     

用C51系列单片机设计物体分级设备的测量光幕

首先介绍了光幕测量高度的原理 ,给出了高度测量光幕的一种实现方法 ,分析了由该方法设计的系统结构和主要性能。从而彻底解决了相邻通路间的干扰 ,提高了测量精度。     

基于MAPINFO和VB的自来水管网信息系统的建立

介绍基于MapInfo平台，利用VB语言进行二次开发，建立自来水管网地理信息系统的关键技术及其注意的问题。     

Prediction and quality control of the melt index during production of high-density polyethylene

In polyolefin processes the melt index (MI) is the most important control variable indicating product quality. Because of the difficulty in the on-line measurement of MI, a lot of MI estimation and correlation methods have been proposed. In this work a new dynamic MI estimation scheme is developed based on system identification techniques. The empirical MI estimation equation proposed in the present study is derived from the 1 ^st -order dynamic models. Effectiveness of the present estimation scheme was illustrated by numerical simulations based on plant operation data including grade change operations in high density polyethylene (HDPE) processes. From the comparisons with other estimation methods it was found that the proposed estimation scheme showed better performance in MI predictions. The virtual sensor model developed based on the estimation scheme was combined with the virtual on-line analyzer (VOA) to give a quality control system to be implemented in the actual HDPE plant. From the application of the present control system, significant reduction of transition time and the amount of off-spec during grade changes was achieved     

The influence of Mgon the formation of calcareous deposits on a freely corroding low carbon steel in seawater

The purpose of this study was to determine how magnesium in seawater influences the corrosion behaviour of freely corroding steel. This was done by studying if Mg(OH)₂ is formed and if calcite and aragonite differ in their protective properties. No Mg(OH)₂ was detected after immersion of steel in a Mg²⁺-containing artificial seawater. Magnesium seems to influence the corrosion behaviour of freely corroding steel by causing calcium carbonate to precipitate as aragonite. Aragonite is more effective in covering the surface than calcite and is therefore more functional in preventing oxygen from reaching the steel surface, thereby lowering the corrosion rate.     

On-line corrosion monitoring in geothermal district heating systems. II. Localized corrosion

Corrosion monitoring in district heating systems has traditionally been performed by using off-line methods, such as weight loss. The disadvantage is that the method is very slow, especially in low-corrosive environments, and that it only provides information about the past corrosion (accumulated over period of time). The purpose of the work is to test on-line monitoring methods in geothermal hot water in the district heating system in Reykjavik, Iceland. Geothermal water poses certain problems with regards to corrosion monitoring due to low conductivity, high pH and the presence of sulphide. These conditions make the geothermal environment low corrosive. However, a quality control is needed, especially since the sulphide causes the steel pipes to be more vulnerable towards localized corrosion. The methods used in this study were: linear polarization resistance (LPR), harmonic analysis (HA), electrochemical noise (EN) and zero resistance ammetry (ZRA). The Pitting Factor was measured with EN and showed promising results for measuring-localized corrosion on-line. A crevice corrosion cell also gave good results but had a low lifetime. However, the results of a galvanic corrosion cell (Fe/Cu) proved more difficult to interpret since they were dependent both on the dissolved oxygen and the sulphide level.     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.     

高频数字锁相环的研究

论文阐述了１００ＭＨｚ数字锁相环的设计过程，用１０ＭＨｚ晶体振荡器对１００ＭＨｚ数字压控振荡器进行锁相，使１００ＭＨｚ输出信号指标得到很大改善。论文还分析了各单元电路，关键点时域波形测试，频谱测试。