秸杆材料用作草皮栽培基质的研究

本文介绍了秸杆毡的成型工艺 ,通过植物所需的水、肥料和空气三种因素对秸杆毡的化学和物理性能进行了研究 ,该材料可被用作草皮栽培基质     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.     

浅谈冲压模具的维修要领及常见故障的排除

介绍冲压模具修理和检查各环节的主要工作内容及维修要领 ,列举了常见故障的排除方法 ,通过总结实际生产中的修模经验 ,对缩短修模周期 ,降低成本 ,延长模具寿命有一定的参考价值。。     

全球趋向统一的《粉末冶金零件材料规范》

评述了ISO 5 75 5“烧结金属材料—规范”和美国MPIF标准 35的变迁和趋向统一。阐述了“最小强度值”的意义。说明了我国粉末冶金结构零件材料标准的现状     

测定钠中杂质的手动阻塞计的研究

文章介绍了测定钠中杂质浓度的手动阻塞计的原理、装置和实验结果。为了减少测量误差,我们研究了影响准确测定阻塞温度的因素,并且找到了减少测量误差的办法。在同样的杂质饱和温度下,该阻塞计测得的高、低阻塞温度所对应的杂质浓度差是很接近的。对氧其差值为1.03ppm;对氢为0.0763ppm。     

High temperature controlled atmosphere experiments for catalysts in a transmission electron microscope

A new transmission electron microscopy (TEM) specimen preparation procedure for high temperature experiments using a controlled atmosphere specimen holder (HTCASH) has been developed. It is designed for studying the microstructure of catalyst specimens before and after treatments in various gases. The procedure involved (1) finding a new formula for the embedding material, (2) devising a new method of making specimen supports, and (3) developing a method for removing the embedding material after the specimen has been microtomed. These techniques were then brought together to produce the ideal specimens for the HTCASH experiments. As an extra benefit, this procedure is also suitable for preparing specimens for ultrahigh resolution imaging experiments. The application of the new procedure in HTCASH experiments is illustrated through a high temperature reduction of a Co/SiO₂-923 catalyst.     

现代住区规划的几点思考

通过对居住区规划中住区交通组织、环境建设,以及住宅配套现实处理方法的分析,指出现代住区的规划要根据当地实际情况,因地制宜组织住区交通网络,合理整合住宅内外环境,适度超前建设配套设施。     

寒区沥青胶浆延性研究

首交提出了沥青胶浆延工的概念，并测定、分析了两种寒区沥青、四种粉胶比在四个温度下的沥青胶浆延度。认为沥青胶浆延度较沥青延度更能反映沥青混合料的流变性能，而且胶浆延度与温度、粉胶比之间有很好的相关性。     

电脑提花圆机图案的设计与开发

应用当前景流行的图形设计软件Coredraw9.0和Photoshop5.0，设计针织面料T恤花型，进一步利用SCC4F-548型电脑提花圆机相配套的图形设计软件Aupaint处理，生成提花花型图案，为夏季T恤花型图案设计提供了一条简便快捷的设计方法和新的设计思路。