X80焊管H_2S环境应力腐蚀开裂行为研究

采用三点弯曲加载法和微电极扫描测试技术,研究了X80高强度级管线钢及其焊缝区的抗H2S环境应力腐蚀开裂(SSCC)行为。测定了焊接接头的显微硬度分布,分析了显微组织结构、力学性能及抗腐蚀性能之间的相关性。研究表明,热影响区(HAZ)对应力腐蚀开裂最为敏感,母材的纵向和横向取样对应力腐蚀敏感性影响不显著,薄壁管材比厚壁管材有较好的抗H2S环境应力腐蚀性能。HAZ晶粒粗大、硬度高,局部腐蚀倾向大,由此导致该区SSCC敏感性高。     

不锈钢管道坡口加工的新方法

对于不锈钢管及合金钢管坡口的加工,采用以往的加工方法切割出来的坡口一般参差不平、比较粗糙,难于打磨平整。使用LGK空气等离子切割机和磁力管道切割机的组合加上一定的辅助手段,改善了不锈钢管及合金钢管的坡口加工效果,使加工出来的坡口像碳钢管一样平整,更加容易打磨组焊。文章介绍了这一新方法所用的设备、材料、切割原理以及操作过程。     

FCC油浆提高废胶粉改性沥青热存储稳定性试验

废胶粉用FCC油浆进行预处理后用于沥青改性,制备出沥青与胶粉间相容性好、高温存储性能稳定的胶粉改性沥青.考察并得出相关工艺条件,同时应用多种评价手段分析改性后沥青的性能,结果表明,预处理后胶粉改性沥青的高温存储性能稳定,低温时柔韧性、抗开裂性能明显提高,高温时稳定性、抗车辙能力及弹性回变性能增强,沥青粘弹区间明显变宽.     

水泥砂浆衬里在输水钢管内壁防腐中的应用

结合工程实例,阐述了在输水水质腐蚀性不大的情况下,输水钢管的内壁防腐采用水泥砂浆衬里的必要性和优点,并介绍了设计要点和安装施工注意事项。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

Niobium-containing catalysts—the state of the art

This review article is devoted to the materials containing niobium, which have been discovered or developed in the past few years and exhibit the potential application in heterogeneous catalysis. Niobium oxides and mixed oxides as well as sulfides, nitrides (oxynitrides), carbides (oxycarbides), and phosphates are considered. Among the catalytic processes in which Nb-containing materials were tested, liquid and gas phase oxidation is described in details, and the role of niobium in the prevention of the catalyst from SO₂ poisoning is mentioned.     

热镀锌板(卷)工程设计中的环境保护问题

对热镀锌板(卷)的生产工艺、主要生产设备进行了简要介绍，并就其污染源(工序)、生产过程中产生的污染物及其控制措施进行了评述，同时就设计和生产中宜注意的几个环保问题进行了分析。     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

基于C6711处理器cdma2000 1X系统前向信道信号的处理

在cdma20001x前向信道中,要对一段信号进行传送,一般选用QPSK调制,因为QPSK调制比QAM更适合噪音环境。采用TI6000系列的TMS320C6711芯片处理前向信道信号,可以对复杂性和实时性较高的信号做采集、量化、编码、调制等实时处理,主要功能通过软件编程实现,从而使系统具有结构灵活、可靠性高、可扩展等优点。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。