基于相变产物构建DP1180相变动力学方程研究

摘要：DP1180钢相变动力学方程的构建,有利于其力学性能的精准调控。利用Gleeble 3500对DP1180钢进行相变点测定,结合切线法、金相 硬度法研究了DP1180钢在冷却过程中的显微组织演变规律,绘制连续冷却转变曲线(CCT),并基于相变产物对相变动力学方程（JMAK方程）进行了修正。结果表明：冷速为0.5~1℃/s时,组织为铁素体(F)和贝氏体(B);冷速为2℃/s时,有马氏体(M)出现;冷速为10℃/s时,组织为贝氏体(B)和马氏体(M);冷速大于20℃/s时,组织以马氏体(M)为主;显微硬度随冷速的增加而升高;基于不同相变产物对n值的影响规律,对传统JMAK方程进行修正,构建了基于相变产物的相变动力学方程,预测精度得到提升。     

球团回转窑建模与仿真的研究进展

摘要：回转窑是一种高温处理物料的热工设备,充分了解回转窑内发生的物理与化学变化对生产具有指导意义,而人眼观察或利用仪器等方式难以探查窑内情况。为掌握回转窑内处理物料的情况并提高生产效率,国内外利用建模与仿真的方法模拟回转窑结构、窑内热场、物料运动。现有模拟已经涉及到了回转窑整体、窑壁、耐火材料、烟气、燃料、火焰、物料等,并利用建模与仿真结果研究了回转窑结构参数及生产参数对部分现象的影响。根据窑内不同区域,综述了回转窑建模与仿真的进展,汇总了建模与仿真的方法与过程及部分参数对回转窑生产的影响。回顾与分析现有的回转窑建模与仿真成果,有助于优化回转窑设备结构的设计及回转窑生产。     

节能降碳的蓄热式加热炉烟气反吹关键技术

摘要：蓄热式加热工艺是大型钢铁企业轧钢工序普遍采用的加热技术,但该工艺高频率换向蓄热燃烧导致公共管道内的燃气交替排入大气造成环境污染和能源浪费,使其成为钢铁生产流程中少有未进行污染物治理的生产工序。基于消除蓄热式加热炉热工制度缺陷,系统介绍了蓄热式加热炉烟气反吹扫技术及与之匹配的加热炉烟气反吹安全联锁与防爆技术、烟气反吹工艺设计与时序调控技术。该成果应用于某钢铁企业蓄热式加热炉（160t/h）建设国内首套换向残留燃气反吹技术示范线,该加热炉燃气放散体积分数由9.0%降低至0.208%,CO放散减排率达92%以上,轧钢燃气耗量节约4.38%。其后承建多家钢铁企业19条蓄热式轧钢加热炉烟气反吹改造工程,均取得较好效果,节能、环保及社会效益显著,同时减少碳氧化物的排放量,助力国家实现双碳目标。     

复吹转炉“留渣 双渣”脱磷工艺试验

摘要：在国内某转炉钢厂采用“留渣 双渣”工艺技术进行脱磷工艺试验。结果表明：随着转炉前期脱磷率不断升高,终点脱磷率不断提高。铁水硅含量对前期脱磷率的影响最大。根据铁水成分,在冶炼前期适当降低供氧强度、降低气固氧比、加入适量石灰及烧结矿,均有利于前期脱磷率的提高。在一倒时每吨钢液加入4~8kg石灰,不影响出钢温度,可提高一倒-终点阶段脱磷率,同时可提高终点脱磷率。从终点的控制效果可知,终点炉渣碱度应保持不小于3.0,炉渣中FeO质量分数在16%~20%,并适当降低终点出钢温度在1610~1630℃,有利于终点脱磷率的提高。通过加强熔池搅拌,促进钢渣反应趋于平衡,有利于终点磷分配比提高,从而可进一步提高终点脱磷率。     

Passivation of Fe-Cr alloys studied with ICP-AES and EQCM

The response of sputter deposited Fe-15Cr and Fe-25Cr alloys to a rapid potential increase in the passive region was studied using two in situ methods: electrochemical quartz crystal microbalance and inductive coupled plasma-atomic emission spectroscopy (ICP-AES). Both methods indicated an increase in the dissolution rate of iron following the potential change; the total amount of material dissolved being higher for the Fe-15Cr alloy. For both alloys, about 10% of the total dissolved material was Cr. This result compared well with experiments on a 430 stainless steel. ICP-AES is shown to be useful for the in situ determination of partial currents of metal dissolution using solution analysis in a flow cell.     

Influence of alloy ingredients on mechanical properties of ternary boride hard alloy clad materials

Using Mo, B-Fe alloy and Fe powders as raw materials, and adding C, Cr and Ni ingredients, respectively, or C, Cr and Ni mixed powders, ternary boride hard alloy clad materials was prepared on Q235 steel substrate by means of in-situ reaction and vacuum liquid phase sintering technology. The influence of alloy ingredients on the mechanical properties of ternary boride hard alloy clad materials was investigated. The results indicate that a mixture of 0.8% C, 5% Cr and 2% Ni ingredients gives a ternary boride hard alloy clad material with optimal mechanical properties, such as high transverse rupture strength, high hardness and good wear resistance.     

Corrosion-Electrochemical behavior of 13% chromium (Cr) martensitic stainless steel in hydrochloric acid (HCl) solutions

Corrosion-Electrochemical behavior of a commercial API5CT grade L80 type 13Cr tubing enriched with microalloying elements is studied in 6, 7.5, 9, 12 and 15% HCl solutions by electrochemical methods. The objective is to contribute to the comprehension of corrosion phenomena caused by HCl of similar concentrations, generally used in acidizing job. The corrosion morphology is examined by scanning electron microscopy (SEM) coupled with EDAX. The soluble corrosion products are analyzed by atomic absorption spectroscopy and colorimetric methods. General, as well as localized, corrosion is present. The severest general corrosion with a maximum rate of 26 mm/year is obtained at 15% HCl. The localized corrosion which morphologically differs as function of HCl concentrations is revealed by SEM investigation. In all the above HCl solutions, the commercial 13% Cr martensitic stainless steel tubing shows no passive state. Above 6% HCl, the microalloying elements promote forming a discontinuous film of the corrosion products. The corrosion rate slightly decreases in 15% HCl compared to the published data on a conventional 13% Cr martensitic stainless steel tubing. This is due to both the chemical composition (silicon, manganese and vanadium) and microstructural properties. Copper seems to additionally accelerate the corrosion of the alloy. Published in Russian in Zashchita Metallov, 2007, Vol. 43, No. 4, pp. 372–380. The article was translated by the authors in English.     

热变形对多元合金耐磨铸铁组织和性能的影响

研究了热变形量对多元合金耐磨铸铁组织和冲击韧度的影响，结果表明，热变形能改变耐磨铸铁组织中共晶碳化物的形状与分布，促进颗粒状碳化物的析出，提高耐磨铸铁的冲击韧度。当该耐磨铸铁的热变形量为40％时，其冲击韧度最佳。     

消失模铸造在轧臼壁生产中的应用

介绍了用消失模铸造生产圆锥破碎机轧臼壁的工艺过程,实践证明,用消失模工艺生产的轧臼壁具有工期短、成本低、成品率高、铸件表面质量高等特点.