Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

微型生化分析仪样品室温度控制系统研究

结合微型生化分析仪样品室的要求,设计了一种基于单片机的微型生化分析仪样品室温度控制系统.它以AT89S51为核心,采用单总线高精度数字温度传感器DS18B20对样品室温度采样,同时利用汇编语言编写温度设定与控制程序,采用半导体制冷的方式,实现了温度在25℃、30℃、32℃和37℃四个温度值的稳定,控制精度达±0.5℃.     

Recent advances in isotropic conductive adhesives for electronics packaging applications

Isotropic conductive adhesives (ICAs) have recently received a lot of focus and attention from the researchers in electronics industry as a potential substitute to lead-bearing solders. Numerous studies have shown that ICAs possess many advantages over conventional soldering such as environmental friendliness, finer pitch printing, lower temperature processing and more flexible and simpler processing. However, complete replacement of soldering by ICAs is yet not possible owing to several limitations of ICAs which are mainly related to reliability aspects like limited impact resistance, unstable contact resistance, low adhesion and conductivity etc. Continued efforts for last 15 years have resulted in development of ICAs with improved properties. This review article is aimed at providing a better understanding of ICAs, their principles, performance and significant research and development work addressing the technological utility of ICAs.     

Irving B. Harris: A Legacy of Vision and Generosity.

Presents a brief tribute to Irving B. Harris upon his passing. Harris played a central role in launching the Harris School of Public Policy Studies and the Center for Human Potential and Public Policy at the University of Chicago. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

VSC8150在波分复用系统开销提取中的应用

波分复用系统将不同波长的光复用在一起进行传输,以满足对传输容量和传输距离的各种需求。介绍了一种开销监视与提取的设计方法,使用VSC8150提取承载在波分复用系统相应波长上SDH信号的开销。分析了VSC8150的工作原理,管脚和外部接口,以及与FPGA、单片机共同完成B1重新计算,开销提取,B1,J0提取。此外,还提出将帧丢失,帧失步等错误状态传送给单片机和网管的方法。本设计增强了波分复用系统网管管理参数,功能和灵活性,这会在系统维护时带来较大的方便。该设计已经成熟应用在实际的波分复用系统中。     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Sintering studies of nano-crystalline zinc oxide

Sintering and grain growth of nano-crystalline undoped ZnO has been studied in detail over a wide range of temperature and holding time. Below 800 °C, sintering of over 70% theoretical density is not observed, irrespective of particle size. At 900 °C for 6 h, the nano-crystalline sample sinters to 99% of theoretical density whereas the density for as received sample is 93% of theoretical density. However, at 1300 °C or higher, the densification is found to be much faster and after a few hours becomes independent of holding time. Grain growth studies reveal a similar feature of attaining saturation over holding time. The average saturated grain size is found to be ∼1.5 and ∼2.2 μm at 800 and 900 °C, respectively, while at 1300 °C or higher, it is in between 12 and 13 μm.     

Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.     

Micromechanical approach to damage mechanics of composite materials with fabric tensors

The purpose of this study is to apply continuum damage mechanics – introduced through the concept of fabric tensors – to composite materials within the framework of the theory of elasticity. A directional data model of damage mechanics for composite materials will be developed using fabric tensors. The introduction of fabric tensors into the analysis of damage of composite materials will allow for an enhanced and better understood physical meaning of damage. The micromechanical approach will be used here to relate the damage effect through fabric tensors to the behavior of composite materials. In this approach, damage mechanics is introduced separately to the constituents of the composite material through different constituents’ damage effect tensors. The damaged properties of the composite system as a whole can then be obtained by proper homogenization of the damaged properties of the constituents.

The derivation of a generalized formulation of damage evolution will be shown here in a mathematically consistent manner that is based on sound thermodynamic principles. Numerical examples will be presented to show applicability. In addition, damage evolution for the one-dimensional tension case is also illustrated.     

中兴宽带线路测试技术及功能介绍

宽带线路测试是中兴通讯ZXDSL综合宽带运维系统的核心功能，在DSL业务提供过程中主要应用在开通前的预测试、线路测试、开通后的例测试以及故障时的在线测试。对其测试技术和功能作了介绍。