低压低渗气藏钻探过程中的保护方案

针对鄂尔多斯塔巴庙区块低压低渗气藏物理特性复杂的情况，推荐一套切实可行的气层保护方案。即实行全面钻井液监控；采用欠平衡钻井技术；储层保护前期研究；采用与地层流体配伍性好的阳离子钻井液体系；降低钻井完井液的滤失量，API滤失量小于5mL、高温高压滤失量小于15mL、固相含量小于8％、含砂量小于0．3％；根据储层裂缝的宽度和走向使用保护剂；对裸眼完钻的气层利用洗井清除井壁附近的污染带，恢复储层原始渗透率；固井作业防止气窜；采用具有抑制地层水敏、速敏保护气层的优质射孔液；水力压裂优化压裂设计，严格压裂施工。总之，气层保护技术是一个系统工程，任何一个环节的问题，都将对气层产生伤害．因此需加强气层保护研究，做到在钻开气层到投产的每道工序都采取积极有效的气层保护措施。     

甲醇蒸汽转化炉炉管损伤分析及修复

通过对乙烯厂甲醇车间蒸汽转化炉炉管的材料成分、力学性能、金相组织等的分析，确定定其失效模式为高温蠕变损伤，找到造成及影响炉管失效的主要因素。并对炉管的修复以及预防提出了有效的方法及建议。     

Damage and strain in pseudomorphic vs relaxed GexSi1−x layers on Si(100) generated by Si ion irradiation

We compare both the strain and damage that 100 keV Si irradiation at room temperature introduces in pseudomorphic and relaxed Ge_xSi_1−x films grown on Si(100) substrates. The ion range is such that the Si/Ge_xSi_1−x interface is not significantly damaged. The amount of damage produced in pseudomorphic and relaxed Ge_xSi_1−x layers of similar x for irradiation doses up to 2.5 × 10¹⁴ Si/cm² is the same, which proves that a pre-existing uniform strain does not noticeably affect the irradiation-induced damage. However, the irradiation-induced strain does depend on the pre-existing strain of the samples. Possible interpretations are discussed. On leave from Inst. voor Kern en Stralingsfysika, Catholic University of Leuven, Belgium.     

A finite element parametric study on the mechanical properties of J-shaped steel hysteresis devices

The present paper discusses the mechanical properties of J-shaped steel hysteresis devices, abbreviated to “J-dampers”, interposed between the upper structure of a spatial structure and its substructure. The mechanical properties of a J-damper, which are characterized by its key geometrical and material parameters, are evaluated through parametric analyses using an in-house Finite Element program. The hysteresis behavior of a J-damper is also modeled by a bi-linear elasto-plastic hysteresis model with the strain-hardening effect. Its elastic stiffness, yield strength and dimensionless hardening ratio, which are expressed as functions of the parameters, are formulated on the basis of mathematical models and the results of parametric studies. Finally, some remarks relevant to the application of the proposed hysteresis model are made for the design of the J-damper.     

A Method of Combined SHPB Technique and BP Neural Network to Study Impact Response of Materials

Abstract:  A new method combining the split Hopkinson pressure bar (SHPB) technique with the back-propagation (BP) neural network program is proposed. By this method, the treated strain wave signals become smooth with less noises induced by the transverse inertia. Moreover, the dynamic rate-dependent constitutive behaviour of materials can be identified, without any pre-assumption of a constitutive model. It is found that by taking the experimentally measured data of strain, strain rate and time as 'input' and the corresponding data of stress as 'output' of the BP neural network, the dynamic constitutive behaviour with internal damage or phase transformation evolution is easy to be identified, where the time could represent either the internal damage evolution or phase transformation process accompanied with the deformation process. It is emphasised that the data learnt by the BP neural network must include both loading and unloading processes, if the whole loading and unloading response is to be correctly predicted. The comparisons between the predictions and experimental results are in good agreement for both polyamide (PA) polymer (as an example of nonlinear viscoelastic materials) and Ti–Ni alloy (as an example of superelastic materials with stress-induced phase transformation).     

Experimental validation of FE predicted fracture behaviour in thermally sprayed coatings

The fracture behaviour of a brittle coating on a substrate is not only governed by its intrinsic fracture strength, but also by a range of other parameters. In order to be able to understand (and thus predict) the fracture response, it is very important to accurately determine the key coating properties such as elastic modulus, residual stresses and fracture strength. In the present work, the fracture behaviour of three different high velocity oxy-fuel (HVOF) sprayed WC–17% Co coatings on Ti–6Al–4V substrates was studied using four-point bending with the acoustic emission technique. The key coating properties were determined experimentally and finite element (FE) models incorporating these experimentally measured properties were used to predict the cracking behaviour. It was found that the FE model was able to predict the differences in the fracture responses of the three coating types based upon differences in their mechanical properties, which in turn enabled the properties which dominate the fracture response to be identified. Moreover, the ability to predict the fracture behaviour of the coatings provided validation of the physical basis of the FE model.     

ABS塑料工件的车削加工

详细介绍了ABS塑料工件车削加工的特点，根据ABS车削加工过程中切削力小、切削温度低，热导率小、线膨胀系数大、弹性模量小的特点，需正确选择车刀的几何参数。     

陕北富县探区天然气藏钻井液屏蔽暂堵技术

陕北富县探区上古生界储层属低孔、低渗的致密储层,下古生界主要储集空间为溶蚀孔洞和裂缝,孔洞多为1～3 mm的小孔,裂缝宽度为0.2～7.0 mm,油气主要聚集在裂缝中.优选出了由复合暂堵剂CXD、憎水性屏蔽剂DYC和表面活性剂ABA组成的屏蔽暂堵配方,其中CXD具有架桥作用并对裂缝性储层有独特暂堵效果,DYC有浊点效应、能在井壁上快速形成阻止滤液侵入的油膜,ABA能减少水锁损害.加入暂堵剂后的钻井完井液,抑制性增强,页岩回收率在90%以上;高温高压滤失量降低,滤饼薄而韧、光滑;岩心静态渗透率恢复值大于90%;滤饼摩阻系数降低.富古6井通过使用该完井液,堵塞比和表皮系数都在轻微污染范围内,井径扩大率比其它井有不同程度的降低,表明优选出的屏蔽暂堵钻井完井液,能很好地保护陕北探区天然气藏.     

原油沥青质沉积引起储集层损害的室内评价

防止沥青质沉积造成的储集层损害是渤海稠油油藏开发生产中遇到的技术难题之一。结合渤海SZ36-1油田实际情况，使用岩心流动实验装置，建立沥青质沉积导致储集层岩心渗透率下降的室内评价方法，并应用SARA法对稠油发生沥青质沉积的可能性进行预测。评价实验结果表明，损害程度与沥青质沉积量和储集层岩心的原始渗透率有关。沉积量越大，原始渗透率越低，则损害越严重。表5参12     

Experience with Siberian Centralized Dispatch Regulation regarding location determination of damages sustained by intersystem high-voltage transmission lines

A set of measures that can be implemented by the Relay-Protection and Automated-Equipment Service for Centralized Dispatch Regulation (CDR) in Siberia to determine the location of damage sustained by inter-system 550-and 220-kV transmission lines maintained by the United Power System (UPS) of Siberia, and the methodology and technology of damage-location determination (DLD) are described. The damage sustained by the 500-kV high-voltage lines (HL), and the accuracy of DLD relative to zero-sequence emergency parameters are analyzed statically. __________ Translated from élektricheskie Stantsii, No. 5, pp. 59–62, May, 2006.