Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

原始组织及加热方式对Al-5.8wt%Cu合金熔化行为的影响

利用DSC分析手段，研究了具有3种不同凝固组织的Al-5.8wt%合金在7种不同加热方式下的熔化开始温度和熔化热，发现凝固组织中存在的非平衡共晶在加热过程中大部分扩散溶解，溶入基体，剩余部分参与共晶熔化，其熔化开始温度与组织状态无关，随加热速度的增大略有升高，溶解部分的体积分散与组织状态和加热方式有关，随加热时间和非平衡相表面积的增大而增大。     

钛合金的银脆,镉脆敏感性及其控制

利用慢应变速率拉伸技术（ＳＳＲＴ），并结合恒载实验，较全面地研究了Ｔｉ－６Ａｌ－４Ｖ合金的银脆行为、固态与液态镉脆行为，确定了应变速率、接触条件、热处理制度、试样取向、温度等因素对Ｔｉ－６Ａｌ－４Ｖ合金银脆与镉脆敏感性的影响，探讨了Ｎｉ阻挡层对控制Ｔｉ－６Ａｌ－４Ｖ合金和ＴＣ１１合金银脆开裂的作用。     

HSLA-80/100钢的焊接

对ＨＳＬＡ－８０／１００钢的焊接性、焊接材料及焊接工艺进行了综述，并指出了现存在的主要问题。     

铝合金高速船船体建造工艺

简述了ＬＦ１５和ＬＦ１６两种新型船用耐蚀可焊铝合金及其配套焊接材料在实船建造中的应用情况。阐述了铝合金全焊结构船体建造的关键技术及我国铝船体建造的３种方法     

Effect of local alloy disorder on the emission kinetics of deep donors (DX centers) in AlxGa1-xAs

In this paper we summarize our recent studies of the effects of local alloy disorder on the properties ofDX levels. A single emission rate is observed in GaAs where all Si-donors have identical local environments. In contrast, three discrete emission rates are observed in dilute AlGaAs alloys, suggesting that the group IV donor moves towards the interstitial site, thereby “selecting” three of the twelve surrounding group III atoms. We present evidence for an ordering of theDX levels consistent with Morgan’s model of a deepening potential well for theDX level as Al atoms are subsequently substituted for Ga atoms near the relaxed donor. These conclusions are consistent with earlier calculations of Chadi and Chang.     

施加复合电磁搅拌对A357合金微观组织的影响

在半固态加工技术中，电磁搅拌是最早应用于制备非枝晶浆料的方法之一，同时也是半固态触变压铸技术最早获得工业应用的重要技术基础之一。采用自行开发的电磁搅拌器，研究了多种不同电磁搅拌方式在不同工艺条件下，单独施加或复合施加对A357合金微观组织的影响。试验结果表明：单一施加旋转感应电磁搅拌时，浆料径向组织很不均匀；单一施加无芯感应电磁搅拌。当搅拌电流较小时，径向组织也不均匀，增大电流，浆料质量有明显改善；采用（旋转感应＋无芯感应）复合电磁场进行复合电磁搅拌时，可在电流较小时获得满意的浆料质量。     

Development of ultra light magnesium-lithium alloys

Magnesium-lithium alloys are among the lowest density metallic materials. Addition of lithium, with a relative density of 0·53, in magnesium reduces the density of the alloy significantly. Furthermore, addition of nearly 11 wt.% lithium converts hexagonal close packed structure of pure magnesium to a body centered cubic lattice, markedly improving formability of the alloy. The development of these alloys, however, had been hampered due to the high reactivity of lithium and magnesium in the molten state and also, due to poor creep resistance and instability of mechanical properties at room temperature. In an attempt to indigenize these ultra light alloys for possible applications in Indian satellite programme, detailed research work was initiated in DMRL. The difficulties associated with producing sound cast ingots have been overcome by controlling melting and casting parameters of these alloys. Extensive work has been done on structure-property correlation of alloys with varying lithium content and minor alloying additions. Based on these work, advanced magnesium-lithium alloys have been developed with improved tensile properties, room temperature stability and creep resistance. Wrought products (plates/sheets) of magnesium-lithium alloy have been supplied to ISAC, Bangalore and are being used in their INSAT-2 programme. This paper describes the systematic studies carried out in the laboratory to indigenize these ultra light alloys.     

Cu－Zn－Al合金中贝氏体的有序性

本文用Ｘ射线研究了Ｃｕ－２０Ｚｎ－６Ａｌ（ｗｔ％）合金中贝氏体结构的有序性，并与马氏体结构进行了比较，实验表明，从高温Ｂ２母相和低温Ｌ２１母相生成的贝氏体中（１１５）和（２０５）衍射峰或（１２１０）和（２０１０）衍射峰是重叠的，对生成的贝氏体进行一段时间的保温或缓慢冷却处理，其衍射峰的特征并不改变，这与马氏体（１１５）和（２０５）衍射峰或（１２１０）和（２０１０）衍射峰的分离特性不相符合。说明贝氏体结构有序度与马氏体明显不同，它的形成不可能继承母相的有序度。