南（昌）长力钢铁公司优化热送热装率生产实践研究

通过对南（昌）长力钢铁公司2号铸坯机以及棒材生产线轧钢产能分析，优化转炉2号铸坯机一轧钢工序产能合理匹配；提高热送热装率的优化技术，该技术的应用不仅提高了棒材生产线生产能力而且节约能源。     

Attitude Controller Design on Variable Rolling Velocity Aerocraft Based on ATmega16

1 Introduction Owing to the effect of crosswind, initial disturbance and the deviation of engine parameters.etc in the initial aviation, variable rolling velocity aerocraft will produce attitude angle deviation (AAD) in the ideal orientations. It must control the attitude of the aerocraft, accordingly, AAD of aerocraft can be amended.Angle stabilization control system is used for the attitude control of rolling aerocraft by this paper. This control system is generally located in the control…     

影响拟薄水铝石烘干系统产能的成因分析及其改进措施

本文针对拟薄水铝石生产线中的关键环节—烘干系统的设备产能问题进行了分析和技术改造,收到了较好的效果,并为同类生产企业及今后改、扩建工作提供了有益的借鉴。     

1270轧机弹性曲线的回归及参数估计

首先介绍了轧机弹性曲线的基础知识及 1 2 70轧机AGC系统的基本结构 ,然后论述了数据采集的方法 ,最后根据最小二乘法得到轧机弹性曲线的回归模型及刚度系数的实验结果。     

Step response classification for model-based autotuning via polygonal curve approximation

A model-based autotuning method consists of an identification and a regulator tuning phase. To achieve satisfactory performance and robustness, it is advisable that both phases be tailored a priori to the characteristics of the observed process dynamics. Such characteristics include, but are not limited to, the model structure. For example, overdamped and underdamped models with the same pole-zero structure are parametrised and controlled in different ways. Step response data, that are typically used for the identification phase in the autotuning context, can also be pre-processed to reveal those characteristics. This paper presents a step response classification method suitable for the above purpose. The method is based on a polygonal curve approximation technique for data pre-processing, followed by a neural network classifier. Only normalised I/O data are employed, so that the neural network can be trained off-line with simulated data. Simulation results are reported to show the effectiveness of the proposed classification method in terms of the achievable tuning results.     

高应力水平下滚动轴承疲劳寿命试验研究

通过在三种不同的强化负荷下进行深沟球轴承疲劳寿命试验，并与常规试验一组结果对比。结果表明，适当地加大滚动轴承疲劳寿命试验负荷，可以大大缩短试验时间，而疲劳寿命依然服从Ｗｅｉｂｕｌ分布，且与常规试验结果基本一致，同时疲劳破坏的形式仍是表面下萌生裂纹，然后扩展至表面形成剥落。     

S—135钢板热轧工艺研究

S—135钢板是水电站用高强耐磨不锈钢板,既要求强度高、韧性好,又要求耐磨、耐蚀性强,生产难度较大。除我厂外,目前国内尚无其它厂家能够生产这种钢板。该钢板在加热轧制,冷却过程中要解决很多技术难点。我们通过采用特殊的控制轧制和控制冷却工艺,很好地解决了诸多技术难点,使S—135钢板的开发研制取得了成功。为电站用高强度耐磨不锈钢生产提供了宝贵的经验,也为控制轧制及控制冷却技术在中板生产行业的应用起到了积极的推动作用。     

Information technology support in the chemical process design life cycle

Information technology has been becoming increasingly important in all areas of engineering during the last few years. Much of the progress achieved in chemical engineering would not have been possible without the enabling methods and tools provided by information technology. This trend will continue in the future but most likely with a considerably wider scope. While individual software tools and services have been in focus until recently, their integration into engineering work processes is an emerging and challenging area of research and development. This contribution attempts to highlight state of the art and future trends in supporting the activities during the life cycle of a chemical process by means of information technology. Emphasis will be largely on the process and plant design process rather than on procurement, manufacturing, and distribution of materials in the supply chain.