MAZDA 620活塞金属型设计

介绍了MAZDA620活塞重力铸造模具的设计方法与过程。模具的设计、制造过程中运用了计算机辅助技术，进行了浇注过程的计算机模拟。发现浇注成形时可能出现的缺陷，并进行合理的改进。针对在试模过程中所出现的气孔和冷隔缺陷，采取了在相应位置上加装导气塞、将模具温度控制在240℃左右和料温控制在780℃等措施，使得该模具在技术上达到使用要求，得到理想的铸件。     

压铸件全自动生产系统的设计与控制

为了满足国际客户对压铸件批量、品质及压铸工艺统计过程控制的要求,使用工业机器人替代程控压铸机取件、喷淋、吹干机械手;增设剪口模用液压机;机器人控制压铸机、液压机及压铸循环,实现压铸件全自动生产。概述了压铸件全自动生产系统的设计和控制方法,并指出了自动压铸工艺的局限性。     

铸件内析出性气孔形成及演化的直接观察与分析

采用透明模型合金实时观察了铸件析出性气孔的形成发展,结果发现,纯物质凝固时,析出性气孔的产生发生于凝固型壳形成之后,随着凝固自型壁向中心凝固,呈现自周边向中心的气条生长。对于合金凝固,析出性气孔在凝固基本完成之后伴随着热裂及缩松的发生开始产生,呈现一定的偏聚现象。浇注前熔体过热度的提高将使析出性气孔更加密集,铸型和环境温度的降低有利于降低气孔的数量及分布范围,采用真空除气,可有效地抑制析出性气孔的产生和热裂缩松缺陷的形成。     

Thixoforging of continuous fiber-reinforced AlSi/AlMg-alloys

High strength in combination with low density is the key features for lightweight constructions in automotive and aerospace applications. Tailor-made fiber reinforcements in light-metal matrices could help to achieve this goal. However, the integration of fibers with conventional casting-route manufacturing techniques like squeeze casting or diffusion bonding restricts the component geometry and results in elevated process cost due to long cycle times and the need of additional fiber coatings. In the center of competence for casting and thixoforging Stuttgart (CCT), new processes for manufacturing metal matrix composites are developed. Long-fiber reinforced Al–Si alloys and components are produced by thixoforging of laminates made of alternating metal matrix layers and carbon fiber fabrics. This paper illustrates the manufacturing technology and first experimental results with special focus on fiber penetration and infiltration behavior and also on the formation of fiber-matrix interface to analyze fiber damage by mechanical or chemical attack.     

跟踪世界铸造新技术

结合工业先进国家铸造技术发展趋势，总结了东风汽车公司近几年来，在铸造材料、铸铁熔化、造型、制芯、砂处理及清理等跟踪先进技术的几项技术成果。     

金属基复合材料实型熔铸颗粒强化技术的研究

把实型铸造与熔铸技术有机结合提出金属基复合材料颗粒强化新技术。通过在实型铸造的泡沫材料的特定部位，事先将高性能合金进行弥散分布处理，浇铸金属母液，在金属结晶凝固过程中，在保持基体材料成分及性能不变的情况下，一次性获得表层或内表层具有特殊性能的金属基复合材料铸件。复合材料层成分、组织由表层向基体呈梯度分布，厚度可控，可以进行机械后加工。     

双辊铸轧AZ91D半固态镁合金板带试验研究

在自行设计、安装的双辊连续、水平铸轧机上进行AZ91D镁合金半固态板带铸轧试验研究，分析了镁合金半固态浆料的制备过程，在590℃左右机械搅拌5min，在550-585℃温度区间内进行铸轧。结果表明，半固态连续铸轧技术可以提高板带的塑性加工性能，细化晶粒。在380℃时进行热轧再加工，最大压下率达到46％。     

热型连铸过程的一维稳态传热模型

根据热型连铸技术原理，建立了热型连铸凝固过程一维稳态温度场的物理、数学模型。通过数值计算，得出了铸型出口温度、冷却距离、拉铸速度和喷水冷却强度等工艺参数对铸坯固液界面位置的影响。计算结果与试验结果吻合。     

Energy Aspects in Drying

The energy performance of a dryer and a drying process is characterized by various indices such as volumetric evaporation rate, steam consumption, unit heat consumption and energy (thermal) efficiency. Of all indices, energy efficiency is the most frequently quoted, in technical specifications. A thorough analysis of available information, including the Handbook of Industrial Drying, points to the inconsistency of terminology, definition and data interpretation. Thus, reported data on energy efficiency vary significantly and frequently contradict both drying theory and industrial practice. To establish a common platform to deal with energy issues, this article provides a concise overview of the most common definitions of energy efficiency, along with a critical review of the published data. A need for energy audit and benchmarking is pointed out. To eliminate shortcomings of the energy efficiency as a lumped parameter, and to allow analysis of energy consumption over time (batch drying) or distance (continuous drying), instantaneous and cumulative indices are proposed. Using these indices, the energy performance of selected dryers is examined, and possible modifications to dryer design and operating parameters are indicated in order to reduce the overall energy consumption.     

多孔β-TCP陶瓷药物载体的制备与体外释药速率的研究

本文用注浆成形的方法制备了以β-TCP为主晶相的多孔药物载体，体外测定了利福平的释药速率。实验结果表明，利福平在模拟体液中能够达到稳定的释放，可以作为骨结核手术后的辅助治疗。多孔β-TCP药物载体有望成为一种理想的药物缓释载体。