一种悬臂式钢管喷印装置及其控制系统

本文介绍了一种用于成品钢管生产线上的悬臂式钢管喷印装置，它是一台结构和功能都较复杂的大型机电一体化设备。文中简介了它的性能、特点和工作原理，对其各部分机械装置的构成及动作以及喷印控制系统的组成和功能进行了较为深入的描述。     

Validity of dynamic electrochemical impedance spectra of some amine corrosion inhibitors in petroleum/water corrosive mixtures by Kramers-Kronig transformation

In our previous works, the corrosion inhibition properties of propylamine (PA), iso-propylamine (i-PA), butylamine (BA), tert-butylamine (t-BA), hexylamine (HA), ethylenediamine (EDA), diethanolamine (DEA), 3-amino-1-propanol (3-AP), 2-dimethylethanolamine (2-DEA), cyclohexylamine (CHA), N-methylcyclohexylamine (N-MCA) and dicyclohexylamine (DCHA) have been investigated by means of electrochemical impedance spectroscopy (EIS) with a carbon steel rotating disc electrode in some petroleum/water corrosive mixtures containing acetic acid and NaCl at 25 °C. In this work, the Kramers-Kronig transformations (KKTs) were applied to evaluate the validity of the impedance data of these amine compounds in hydrodynamic condition. The results obtained showed that experimental impedance data did not satisfy in K-K relations completely viz. indicated some errors. These errors were related to stray capacitances, external transmission line effects, pits formation and change in interface during data acquisition at high and low frequencies regions. In addition, the selection of a suitable equivalent circuit strongly emphasized to better interpret of EIS data which in turn cause better resulted KKTs spectra. With considering obtained transformations, more effective inhibitor was selected with regard to its charge transfer resistance, the corrosion capacitance and well satisfying in K-K relations.     

Morphology and Forming Mechanism of Rare Earth Inclusions During Solidification of Steel

ＭｏｒｐｈｏｌｏｇｙａｎｄＦｏｒｍｉｎｇＭｅｃｈａｎｉｓｍｏｆＲａｒｅＥａｒｔｈＩｎｃｌｕｓｉｏｎｓＤｕｒｉｎｇＳｏｌｉｄｉｆｉｃａｔｉｏｎｏｆＳｔｅｅｌ￥ＺｈａｉＱｉ－Ｊｉｅ（ＤｅｐａｒｔｍｅｎｔｏｆＭｅｔａｌｌｕｒｇｙ，ＵｎｉｖｅｒｓｉｔｙｏｆＳ...     

A simple SCC specimen incorporating heat transfer with a crevice or deposits

A simple stress-corrosion cracking (SCC) specimen, suitable for slow strain rate testing and incorporating heat transfer, with an artificial crevice or deposits has been designed and tested. It appears that when the solute level is above a certain value it can concentrate. The kinetics of solute accumulation and the concentration that can be induced in the specimen have been determined. Build up of solute from the ppm level in the bulk environment to the level required to cause cracking can take hours, not days or years. The limiting concentration reached is controlled by thermodynamics, specifically the available superheat. A brief review of relevant literature suggests that this experimental approach to predicting SCC has significant advantages over a modelling or measurement approach. The specimen also lends itself to a monitoring role--a modern version of the Schroeder embrittlement detector.     

Pit to crack transition in stress corrosion cracking of a steam turbine disc steel

Long term exposure tests have been carried out on a 3 NiCrMoV steam turbine disc steel in the form of cylindrical tensile test specimens self-loaded to 90% of σ_0.2 and exposed to three environmental conditions, viz. deaerated pure water, aerated pure water, and aerated water containing 1.5 ppm of chloride ion. Pitting occurred in all environments but the density and depth of pits in the chloride-containing medium was markedly greater. No cracking was observed in deaerated pure water but cracks initiated in aerated water between 13 and 19 months and in less than 7 months in aerated 1.5 ppm Cl⁻ solution. The probability of a crack initiating from a pit of specific depth in aerated solution could be described well by a Weibull function. Profiling of pits and cracks in the disc steel tested in aerated 1.5 ppm Cl⁻ solution showed that there while there were many cracks with a depth greater than that of the corresponding pit the depth of some cracks was smaller than that of the corresponding pit, suggesting that cracks do not necessarily initiate from the bottom of the pits. The growth rate of short cracks emerging from pits appeared greater than that of long cracks in fracture mechanics specimens.     

RE／S值对控轧低碳Mn－Nb－RE钢硫化物成分和形貌的影响

用扫描电镜测定了含０．０４１％～０．０７６％ＲＥ的低碳Ｍｎ－Ｎｂ－ＲＥ钢中硫化物的成分、大小和形貌。ＲＥ／Ｓ值为２．８～３．０时，钢中的硫化物充分变质。     

调质状态下40Cr钢的焊接

在合理制定焊接工艺的基础上，采用R307珠光体耐热钢焊条成功地进行40Cr钢在调质状态下的焊接，解决了通常采用25—13型奥氏体焊条焊接出现的焊缝强度低、焊接接头性能差的问题。     

Microstructural investigation of the breakdown of the protective oxide scale on a 304 steel in the presence of oxygen and water vapour at 600 °C

This article focuses on the detailed microstructural investigation of the oxide scale formed on a 304 steel in the presence of oxygen and water vapour (40%) at 600 °C. The work has been carried out using a combination of microanalytical techniques including FIB, TEM, EDX and electron diffraction. The local breakdown of the initially protective oxide scale and the growth of island/crater oxide morphology are described. Special consideration is given to the influence of the microstructure of the steel and the oxide scale on the breakdown behaviour.     

高速硬车削淬火钢的实验研究

通过改变高速车削淬火钢（Cr12）的切削用量，对切削力、切削温度、加工表面质量等进行了研究，结果表明合理选择切削用量，高速硬车削淬火钢可显著提高生产率及加工表面质量，并在一定程度上可取代磨削加工。     

Effects of the cryogenic cooling on the fatigue strength of the AISI 304 stainless steel ground components

For environmental considerations, the substitution of the conventionally used oil-based grinding fluids has nowadays become strongly recommended. Although several alternatives have been proposed, cryogenic cooling by liquid nitrogen is the non-polluting coolant that has been given relatively more attention because of its very low temperature. In this investigation, in order to contribute to developing this promising cooling mode, its beneficial effects on the ground surface integrity of the AISI 304 stainless steel and their consequences on the fatigue lifetime are explored. Results of this investigation show that grinding under cryogenic cooling mode generates surfaces with lower roughness, less defects, higher work hardening and less tensile residual stresses than those obtained on surfaces ground under oil-based grinding fluid. These surface enhancements result into substantial improvements in the fatigue behaviour of components ground under this cooling mode. An increasing rate of almost 15% of the endurance limit at 2 × 10⁶ cycles could be realized. SEM analyses of the fatigue fracture surfaces have shown that the fatigue cracks observed on the specimens ground under cryogenic cooling are shorter (i.e., 30-50 μm) than those generated under oil-based cooling mode (i.e., 150-200 μm). The realized improvements in the surface integrity and in the fatigue behaviour are thought to be related to the reduction of the grinding zone temperature observed under cryogenic cooling, as no significant differences between the grinding force components for both cooling modes have been observed.