三辊穿孔和轧管所产生的钢管壁厚极差和波浪形内螺纹

定量描述了实际生产过程中三辊斜轧穿孔所产生的钢管壁厚极差和波浪形内螺纹，初步探讨了三辊轧管机对钢管壁厚极差和波浪形内螺纹的影响。     

一种悬臂式钢管喷印装置及其控制系统

本文介绍了一种用于成品钢管生产线上的悬臂式钢管喷印装置，它是一台结构和功能都较复杂的大型机电一体化设备。文中简介了它的性能、特点和工作原理，对其各部分机械装置的构成及动作以及喷印控制系统的组成和功能进行了较为深入的描述。     

Validity of dynamic electrochemical impedance spectra of some amine corrosion inhibitors in petroleum/water corrosive mixtures by Kramers-Kronig transformation

In our previous works, the corrosion inhibition properties of propylamine (PA), iso-propylamine (i-PA), butylamine (BA), tert-butylamine (t-BA), hexylamine (HA), ethylenediamine (EDA), diethanolamine (DEA), 3-amino-1-propanol (3-AP), 2-dimethylethanolamine (2-DEA), cyclohexylamine (CHA), N-methylcyclohexylamine (N-MCA) and dicyclohexylamine (DCHA) have been investigated by means of electrochemical impedance spectroscopy (EIS) with a carbon steel rotating disc electrode in some petroleum/water corrosive mixtures containing acetic acid and NaCl at 25 °C. In this work, the Kramers-Kronig transformations (KKTs) were applied to evaluate the validity of the impedance data of these amine compounds in hydrodynamic condition. The results obtained showed that experimental impedance data did not satisfy in K-K relations completely viz. indicated some errors. These errors were related to stray capacitances, external transmission line effects, pits formation and change in interface during data acquisition at high and low frequencies regions. In addition, the selection of a suitable equivalent circuit strongly emphasized to better interpret of EIS data which in turn cause better resulted KKTs spectra. With considering obtained transformations, more effective inhibitor was selected with regard to its charge transfer resistance, the corrosion capacitance and well satisfying in K-K relations.     

电子辐照加速器大功率工频高压电源

文章介绍目前两种用于烟气脱硫加速器的不同形式直流高压电源，分析了它们各自的特点。针对它们存在的不足之处，提出了一种全新的倍压型桥式整流线路，并对此线路进行了理论推导和计算机模拟仿真。     

Morphology and Forming Mechanism of Rare Earth Inclusions During Solidification of Steel

ＭｏｒｐｈｏｌｏｇｙａｎｄＦｏｒｍｉｎｇＭｅｃｈａｎｉｓｍｏｆＲａｒｅＥａｒｔｈＩｎｃｌｕｓｉｏｎｓＤｕｒｉｎｇＳｏｌｉｄｉｆｉｃａｔｉｏｎｏｆＳｔｅｅｌ￥ＺｈａｉＱｉ－Ｊｉｅ（ＤｅｐａｒｔｍｅｎｔｏｆＭｅｔａｌｌｕｒｇｙ，ＵｎｉｖｅｒｓｉｔｙｏｆＳ...     

Pit to crack transition in stress corrosion cracking of a steam turbine disc steel

Long term exposure tests have been carried out on a 3 NiCrMoV steam turbine disc steel in the form of cylindrical tensile test specimens self-loaded to 90% of σ_0.2 and exposed to three environmental conditions, viz. deaerated pure water, aerated pure water, and aerated water containing 1.5 ppm of chloride ion. Pitting occurred in all environments but the density and depth of pits in the chloride-containing medium was markedly greater. No cracking was observed in deaerated pure water but cracks initiated in aerated water between 13 and 19 months and in less than 7 months in aerated 1.5 ppm Cl⁻ solution. The probability of a crack initiating from a pit of specific depth in aerated solution could be described well by a Weibull function. Profiling of pits and cracks in the disc steel tested in aerated 1.5 ppm Cl⁻ solution showed that there while there were many cracks with a depth greater than that of the corresponding pit the depth of some cracks was smaller than that of the corresponding pit, suggesting that cracks do not necessarily initiate from the bottom of the pits. The growth rate of short cracks emerging from pits appeared greater than that of long cracks in fracture mechanics specimens.     

RE／S值对控轧低碳Mn－Nb－RE钢硫化物成分和形貌的影响

用扫描电镜测定了含０．０４１％～０．０７６％ＲＥ的低碳Ｍｎ－Ｎｂ－ＲＥ钢中硫化物的成分、大小和形貌。ＲＥ／Ｓ值为２．８～３．０时，钢中的硫化物充分变质。     

调质状态下40Cr钢的焊接

在合理制定焊接工艺的基础上，采用R307珠光体耐热钢焊条成功地进行40Cr钢在调质状态下的焊接，解决了通常采用25—13型奥氏体焊条焊接出现的焊缝强度低、焊接接头性能差的问题。     

高速硬车削淬火钢的实验研究

通过改变高速车削淬火钢（Cr12）的切削用量，对切削力、切削温度、加工表面质量等进行了研究，结果表明合理选择切削用量，高速硬车削淬火钢可显著提高生产率及加工表面质量，并在一定程度上可取代磨削加工。     

公路桥涵台背设计的理论方法探讨

介绍了近年来国内外研究人员对桥涵台背的设计研究方法，结合桥涵与台背结构组合的设计原则，从搭板的型式、坡度、长度、厚度、配筋等方面提出了搭板设计的方法。