Structural modelling of coprecipitated VTiO catalysts

A statistical study of the particle shape and size of pure V₂O₅ and TiO₂, and samples of coprecipitated V₂O₅---TiO₂ catalysts with different V/Ti ratios, has been performed. They were also characterized by XRD, EDAX, SEM and XPS. The results showed that pure vanadium pentoxide is compose by large square or needle-shaped particles, while pure titanium dioxide has small and rounded ones. VTiO samples presented an area and shape, depending on the V/Ti ratio.

These results and the spectroscopical characterization conducted to a particle model of the catalysts. Those VOTi samples with high V/Ti ratio would have large V₂O₅ crystals acting as support of a V/TiO₂ solid solution. In contrast, those samples with a low V/Ti ratio, would have the solid solution supporting vanadium pentoxide crystals.     

Advances in titanium metal injection molding

The approaches to production of titanium powder injection molded parts are reviewed. Historically, oxygen levels have been too high for structural use (particularly with the Ti-6Al-4V alloy). However, recent advances in starting powders, binders and sintering facilities now allow oxygen levels in the Ti-6Al-4V alloy to be controlled to about 0.2 wt.% oxygen. This should result in significant expansion of the titanium PIM market place into aerospace, automobiles, surgical instruments, dentistry, communication devices (such as computers and cell phones), knives and guns. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 5–6 (455), pp. 118–125, 2007.     

Single and combined deactivating effect of alkali metals and HCl on commercial SCR catalysts

Two commercial SCR catalysts, with a nominal W content of about 9 wt.% and a V nominal content of 0.55 and 1.8 wt.%, respectively, were contacted with different amounts of Na and K and with HCl vapours in order to simulate poisoning by species more specifically contained in exhaust gases from MSW combustion. Catalysts were characterised using XRD analysis, SEM/EDX analysis, BET and pore size distribution measurements, NH₃ TPD, TG analysis. Poisoning agents do not cause loss of surface area nor pore occlusion. A significant loss of surface acidity was observed upon alkali metals poisoning whereas a decreasing of vanadium content was observed for the more concentrated catalysts upon HCl poisoning. Catalysts deactivation is proportional to the number of acid sites neutralised by alkali metals adsorbing ammonia in the temperature range typical of SCR process. HCl promotes the formation of new acid sites showing a lower activity compared to the original one.     

基于MSP430的低功耗近距无线图像传输系统设计与实现

近距无线图像传输系统主要用于无线传感器网络中的图像采集、传输、处理和显示,本文设计并实现了一种具有较强实用性的近距无线图像传输系统。采用OV7670图像传感器作为图像数据采集器,高速低功耗的nRF24L01射频模块作为无线收发器,采用MSP430F14916位超低功耗单片机作为微处理器,所构成的系统具有功耗低、图像传输速度快等优点。作者详细阐述了该系统的硬件结构和软件设计。     

Measurement of the heat of fusion of titanium and a titanium alloy (90Ti-6Al-4V) by a microsecond-resolution transient technique

A microsecond-resolution pulse heating technique was used for the measurement of the heat of fusion of titanium and a titanium alloy (90Ti-6Al-4V). The method is based on rapid (50- to 100-s) resistive self-heating of the specimen by a high-current pulse from a capacitor discharge system and measuring, as functions of time, current through the specimen, voltage across the specimen, and radiance of the specimen. Melting of the specimen is manifested by a plateau in the measured radiance. The time integral of the net power absorbed by the specimen during melting yields the heat of fusion. The values obtained for heat of fusion were 272 J · g^–1 (13.0 kJ · mol^–1) for titanium and 286 J · g^–1 for the alloy 90Ti-6Al-4V, with an estimated maximum uncertainty of ±6% in each value.Paper presented at the Second Workshop on Subsecond Thermophysics, September 20–21, 1990, Torino, Italy.     

氧化钒制取碳化钒的热力学分析

采用热力学的方法对以五氧化二钒为原料制取碳化钒的工艺过程进行了分析,分析表明:钒氧化物的转化过程中遵守逐级还原理论。钒氧化物碳化过程中,不转化为金属钒,直接转化为碳化钒。在钒氧化物的转化过程中,应尽可能使其转化为二氧化钒。若采用气相还原碳化的方法,可通过调节气体的流量、配比、还原与碳化工艺参数进行质量控制。     

V2O5/g⁃C3N4催化剂的制备及其模拟油中硫化物的脱除

以三聚氰胺、偏钒酸铵、硼酸为前驱体,通过煅烧法制备V₂O₅/g⁃C₃N₄催化剂。采用XRD、FT⁃IR、XPS、SEM和BET等技术对催化剂的结构与形貌进行表征。以V₂O₅/g⁃C₃N₄为催化剂,乙腈为萃取剂,H₂O₂为氧化剂对模拟油中二苯并噻吩（DBT）的脱除进行考察。探究了反应温度、催化剂质量、萃取剂体积、n(H₂O₂)/n(S)以及不同硫化物等因素对脱硫效果的影响。在模拟油体积为5.0 mL、萃取剂乙腈体积为3.0 mL、n(H₂O₂)/n(S)=8、催化剂质量为0.02 g、反应温度为30 ℃和反应时间为60 min的最佳条件下,DBT的脱除率达到91.9%,经过5次催化剂再生后脱硫率仍可以达到85.7%。     

3Cr2W8V钢强韧化处理研究

本文从强韧化机制方面，研究了用于铝合金型材挤压模具的３Ｃｒ２Ｗ８Ｖ钢在不同热处理工艺条件下的金相组织，显微结构与断口，常温与高温下的力学性能。结果表明，采用１２５０℃以上超高温淬火加４００－５００℃中温回火的强韧化处理工艺，可使该钢同时获得具有良好力学性能和较好韧性、热强性、热稳定性、热疲劳性、耐磨性等相结合的综合性能。     

控轧控冷工艺对高强度锚杆钢组织和性能的影响

随着矿井深度的增加,对锚杆支护强韧性的要求越来越高,为了应对这一情况,需要研发出更高强度的锚杆钢。利用锚杆钢研究了轧制工艺、冷却工艺与珠光体、铁素体相比例,析出相析出行为及力学性能的关系。研究结果表明,在中轧后、精轧前采用适当水冷+回复段处理的复合工艺可使晶粒更细小、组织更均匀。对超高强度锚杆钢进行热压缩变形试验,由热模拟试验结果确定相转变温度为A_c1=737 ℃、A_c3=886 ℃。最终筛选出入精轧温度为810 ℃、回复段温度为800 ℃时,可获得的晶粒尺寸达4 μm,珠光体体积分数为66.8%,铁素体体积分数为33.2%,珠光体片层间距达200 nm;另外调整V、Cr、N等析出以提高锚杆钢的强韧性,较低的回复温度有利于细小、弥散、V(C/N)析出相的析出,V(C/N)的析出可进一步改善锚杆钢的力学性能。由该控轧控冷工艺轧制的锚杆钢屈服强度为780 MPa、抗拉强度为930 MPa、硬度为291HV、伸长率为20%。     

Stress relaxation behavior of Ti-6Al-4V alloy

1　INTRODUCTIONTi 6Al 4VisoneofthemostimportantTial loys[1,2 ] .Butthisalloyhasbadformabilityforitshighelasticresilience .Therefore ,hotsizingisimpor tant[36 ] .Asthebaseofhotsizing ,thestudyofstressrelaxationhasimportanttheoreticalvalueandpracticalsignificance .Ontheotherhand ,Ti 6Al 4Visusedasfastenermaterialssometimes .Whenthefastenersworkatthetemperaturehigherthanroomtemperature ,stressrelaxationmayresultsinacci dents .Sohowtopreventthestressrelaxationisveryimportant[7] .Uptonow ,…