攀钢1450热轧带钢厂精轧机组电动压下机构带钢压下时的动特性计算和探讨

从理论上和实践上对武钢１７００、鞍钢１７００改造前后、本钢１７００改造前后和攀钢１４５０精轧机组的电动压下机构在带钢压下时的动特性进行计算和探讨，得出有说服力的结论。主题词：     

台北101层国际金融中心之结构施工技术与其设计考量概述

本文旨在简要说明目前正在施工中之超高层大楼—台北国际金融中心之结构系统、钢结构工程、钢筋混凝土工程基础与深开挖工程等特殊施工技术,并佐以相关之设计考量与施工规划概要,以供工程界做参考。     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

The microstructure of Cu films deposited by the self-ion assisted technique

The microstructures of Cu films deposited by the self-ion assisted, partially ionized beam (PIB) deposition technique under two different accelerating potentials, 0 KeV and 6 KeV, are compared. The 6 KeV film shows a bimodal (111) fiber and (100) fiber texture with an abundance of twin boundaries and a relatively large average grain size with a typical lognormal distribution. The 0 KeV film consists of small, mostly (111) oriented grains with islands of abnormally large (100) grains. The controlling factors for the abnormal growth of the (100) grains are discussed in relation to the observed microstructures, showing that all factors necessary for abnormal (100) growth are present in the films.     

Evaluation of Monkman-Grant parameters for type 316LN and modified 9Cr-Mo stainless steels

The Monkman-Grant (M-G) and its modified parameters were evaluated for type 316LN and modified 9Cr-Mo stainless steels prepared with minor element variations. Several sets of creep data for the two alloy systems were obtained by constant-load creep tests in 550-650°C temperature range. The M-G parameters,m, m’,C, andC’ were proposed and discussed for the two alloy systems. Them value of the M-G relation was 0.90 in type 316LN steel and 0.84 in modified 9Cr-Mo steel. Them’, value of the modified relation was 0.94 in type 316LN steel and 0.89 in 9Cr-Mo steel. Although creep fracture modes and creep properties between type 316LN and modified 9Cr-Mo steels showed a basic difference, the M-G and its modified relations demonstrated linearity quite well. Them’ of modified relation almost overlapped regardless of the creep testing conditions and chemical variations in the two alloy systems, and the parameterm’ was closer to unity than that of the M-G relation.     

Intermetallic compounds formed at the interface between liquid indium and copper substrates

The interfacial reactions between liquid In and Cu substrates at temperatures ranging from 175°C to 400°C are investigated for the applications in bonding recycled sputtering targets to their backing plates. Experimental results show that a scallop-shaped Cu₁₆In₉ intermetallic compound is found at the Cu/In interface after solder reactions at temperatures above 300°C. A double-layer structure of intermetallic compounds containing scallop-shaped Cu₁₁In₉ and continuous CuIn is observed after the Cu/In interfacial reaction at temperatures below 300°C. The growth of all these intermetallic compounds follows the parabolic law, which implies that the growth is diffusion-controlled. The activation energies for the growth of Cu₁₆In₉, Cu₁₁In₉, and CuIn intermetallic compounds calculated from the Arrhenius plot of growth reaction constants are 59.5, 16.9, and 23.5 kJ/mole, respectively.     

单轴传动滚切式双边剪薄钢板剪后“错牙”及“飞边”的原因分析与对策

针对单轴传动滚切式双边剪生产过程中出现的薄钢板经双边剪剪后出现“错牙”及“飞边”的问题,从多个方面入手对薄钢板出现“错牙”及“飞边”的原因进行了分析对比,提出了相应的解决方案,对今后滚切式双边剪的设计、制造及安装调试有借鉴和参考价值。     

炉衬产生的氧对真空钢液脱氮的动力学影响

采用 99.99%氧化镁砂捣打炉衬的 2 0kg真空感应炉 ,研究了超低碳钢熔炼时炉衬产生的氧对真空钢液脱氮的影响。试验结果表明 :钢液中氧含量在 1 2 0× 1 0 - 6 时 ,脱氮的限制性环节是界面化学反应 ;随炉衬中氧的逸出 ,当钢液中氧含量在 5 1 0×1 0 - 6 时 ,真空钢液脱氮处于界面化学反应和液相边界层扩散控制的边缘区域 ,脱氮速率降低     

Active sites of Cu-ZSM-5 for the decomposition of acrylonitrile

The catalytic decomposition of acrylonitrile (AN) over Cu-ZSM-5 prepared with various Cu loadings was investigated. AN conversion, during which the nitrogen atoms in AN were mainly converted to N₂, increased as Cu loading increased. N₂ selectivities as high as 90–95% were attained. X-ray diffraction measurements (XRD) and temperature-programmed reduction by H₂ (H₂-TPR) showed the existence of bulk CuO in Cu-ZSM-5 with a Cu loading of 6.4 wt% and the existence of highly dispersed CuO in Cu-ZSM-5 with a Cu loading of 3.3 wt%. Electron spin resonance measurements revealed that Cu-ZSM-5 contains three forms of isolated Cu²⁺ ions (square-planar, square-pyramidal, and distorted square-pyramidal). The H₂-TPR results suggested that in Cu-ZSM-5 with a Cu loading of 2.9 wt% and below, Cu⁺ existed even after oxidizing pretreatment. The activity of AN decomposition over Cu/SiO₂ suggested that CuO could form N₂, but, independent of the CuO dispersion, nitrogen oxides (NO_x) were formed above 350 °C. Cu⁺ and the square-pyramidal and distorted square-pyramidal forms of Cu²⁺ showed low activity for AN decomposition. Temperature-programmed desorption of NH₃ suggested that N₂ formation from NH₃ proceeded on Cu²⁺, resulting in the formation of Cu⁺. The Cu⁺ ions were oxidized to Cu²⁺ at around 300 °C. Thus, high N₂ selectivity over Cu-ZSM-5 with a wide range of temperature was probably attained by the reaction over the square-planar Cu²⁺, which can be reversibly reduced and oxidized.     

The influence of Mgon the formation of calcareous deposits on a freely corroding low carbon steel in seawater

The purpose of this study was to determine how magnesium in seawater influences the corrosion behaviour of freely corroding steel. This was done by studying if Mg(OH)₂ is formed and if calcite and aragonite differ in their protective properties. No Mg(OH)₂ was detected after immersion of steel in a Mg²⁺-containing artificial seawater. Magnesium seems to influence the corrosion behaviour of freely corroding steel by causing calcium carbonate to precipitate as aragonite. Aragonite is more effective in covering the surface than calcite and is therefore more functional in preventing oxygen from reaching the steel surface, thereby lowering the corrosion rate.