半不连续切屑流动速度的系统分析及切屑变形的度量

本文借助影片运动分析仪,对用高速摄影记录的钛合金切屑沿前刀面的流动规律进行了研究,并用系统分析法进行了描述,推导出能反映半不连续切屑不均匀变形过程的动态衡量参数,同时也导出了度量此种切屑塑性变形的准静态参数——等效切削比。     

钛元素对铝钛合金中铝含量测定的干扰

在纯铝标样中加入相应的钛元素为标准,采用ＥＤＴＡ滴定法,测试钛元素对铝钛合金中铝含量测定的干扰。实验证明,钛对铝的测定干扰十分严重。文章给出了正确测定铝含量的方法。     

低品位氧化锌粉矿制粒及碱性浸出

小于2 mm的氧化锌矿(含锌5.17%)与5%的水泥混合,制粒并固化,所得颗粒直径5~8 mm。固化3天、10天、45天的颗粒用碱性溶液浸出,最大浸出率分别为92.2%、87.3%、72.9%。减少固化时间能够缩短反应时间、增加颗粒中锌的溶解以及减少浸出剂中初始锌浓度的影响。实验表明颗粒最少需固化3天。动力学研究表明浸出过程受浸出剂通过脉石层的扩散控制,表观速率常数分别为3.51×10-2d-1、8.09×10-3d-1和4.74×10-3d-1。     

基于ABAQUS软件的微米级金属材料性能研究

为工程实践中迫切需要解决微米和亚微米量级的设计与制造问题,文章中运用MSG塑性理论利用Abaqus软件对铝合金的强度及均匀延伸率进行了比较系统的研究;运用有限单元法分析了MSG应变梯度本构方程和经典的弹塑性本构方程对不同晶粒尺寸的铝合金的应力应变关系;模拟不同晶粒尺寸的铝合金的强度及均匀延伸率。结果表明随着晶粒尺寸的减小,屈服强度、应变硬化明显增加,延伸率却往往越小。对于该问题的研究探索,将是解决材料强度与均匀伸长率这对矛盾体的问题关键,同时,为科研工作者提供了新方法和新途径。     

常压H2气氛烧结W-TiC合金的致密化行为和性能

采用粉末冶金方法在常压H2气氛下制备W-TiC合金,研究W-TiC合金的烧结致密化行为,并对合金的性能和组织结构进行分析.结果表明:添加微量强化烧结元素可改善W-TiC合金的烧结活性,在1700℃烧结120min后其相对密度达到99.2％;随着烧结温度的升高,W-TiC合金的拉伸强度提高,在2000℃烧结120 min...     

Editor's Introduction

This paper reviews the state of the art in processing and extraction of ocean floor manganese nodules. It briefly reviews the mining sites where the abundant rich nodules occur and also discusses the metal distribution in nodules in view of economical processing and extraction of these metal values.

The paper discloses in a detailed manner the physical and chemical characteristics of nodules, including porosity, surface area, water content and the effect of temperature on crystal structure of major constituents of nodules.

In the extraction aspect of nodules, the paper reviews two different extraction schemes revealed in the literature, namely hydrometallurgical treatment and pyrometallurgical treatment. The hydrometallurgical treatments include acid leaching, ammonia leaching, leaching with reducing agents and leaching after high temperature pre-treatments such as in sulfating rousting, while the pyrometallurgical processes include smelting, chlorination-vaporization and segregation. The paper also covers metal recovery processes from leach liquor.

An economic survey of processing nodules has been made in terms of problems associated with metal-marketing, and impact of metal production from nodules on mineral industries.     

TC4合金锥体模锻过程的数值模拟

采用刚塑性有限元法对钛合金锥体的模锻成形进行有限元数值模拟,分析了锥形件模锻过程中的金属流动规律,应力场、应变场、变形区的压力分布,压力的变化规律等。模拟结果表明,锥体模锻成形分为3个阶段:初期变形过程是圆柱体变形为一个小曲率壳体的阶段,应力主要集中在上模的正下方,应变主要发生在此变形区;变形中期是与下模相接触的部分参与变形的体积逐渐增大,直至最后形成所需要的锥体形状;变形后期由于摩擦作用产生严重的不均匀壁厚减薄现象。     

预钙化加速类骨磷灰石在镍钛合金表面生长的电化学阻抗谱

通过酸碱处理活化NiTi合金表面,在模拟体液中仿生生长类骨磷灰石层以改善其生物相容性.采用电化学阻抗谱研究了预钙化对加速磷灰石沉积的影响,并基于双层模型建立了电子等效电路.结果表明:随着在模拟体液中浸泡时间的延长,化学处理的NiTi合金表面类骨磷灰石不断生长,并且添加预钙化试样浸泡3 d,即可在合金表面生长出均匀完整的类骨磷灰石层,而未预钙化试样表面沉积物稀少.对应电子等效电路中,预钙化试样电阻值明显大于未预钙化试样的,显示预钙化促进了活化NiTi合金表面类骨磷灰石的生长.     

Zn对AB5型贮氢合金的影响

研究了Zn替代Co对AB5型MlNi3.6Mn0.4Al0.3Co0.7贮氢合金相结构和电化学性能的影响。Zn替代Co使合金的晶胞参数和体积增大,导致贮氢合金最大放电容量增加,循环稳定性有所下降;随着Zn含量由0增加到0.5,氢的扩散系数由0.31×10-7m2/s增加到3.72×10-7m2/s,交换电流密度由157 mA/g增加到191 mA/g,合金极化电阻由1.23Ω减少到1.01Ω,合金表面电催化活性和高倍率性能得到了改善。     

A novel approach for the synthesis of nanocrystalline zinc oxide powders by room temperature co-precipitation method

A single step co-precipitation route has been employed for the first time in the preparation of ZnO nanoparticles using ammonium hydroxide and zinc nitrate tetrahydrate. The X-ray diffraction analysis revealed that the synthesized powder has the hexagonal (wurtzite) structure. The as-prepared ZnO powder was well crystalline, without any calcination. This is a promising result compared to those mentioned in the literature, in which crystallization of ZnO nanoparticles was detected at > 300 °C. The average crystallite size of the as-prepared ZnO nanopowder is 20-40 nm. The nanocrystalline ZnO could be sintered to ~ 95% of the theoretical density at 1300 °C in 4 h.