Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

二氧化碳增油技术在孤岛油田的应用

介绍了二氧化碳增油机理和二氧化碳增油技术在孤岛油田的应用情况。现场应用表明 ,二氧化碳非混相驱油是封闭小断块油田的有效增产措施 ,二氧化碳酸化 (压裂 )助排能起到缩短排液时间 ,保护油气层的作用     

碳纤维增强水泥/混凝土材料力学性能的若干研究

本文通过对水泥基体掺入碳纤维进行研究，得出了复合体抗压强度、劈拉强度与碳纤维掺量的关系。同时文中还利用聚丙烯腈纤维作对比研究，得出目前碳纤维作为增强体的优缺点，为碳纤维增强水泥基复合材料的推广应用提供更多的实验依据。     

Asymmetric Hydrogenation of Activated Ketones on Platinum: Relevant and Spectator Species

The heterogeneous enantioselective hydrogenation of activated ketones over chirally modified platinum is reviewed with emphasis on identifying the role of the various species observed in this catalytic system. The past years have witnessed a continuous broadening of the scope of this catalytic system including new reactants and modifiers affording over 97% ee. New reaction pathways have been uncovered and the kinetic and mechanistic studies have been faced with a number of complicating factors caused by spectator species and interactions in solution and on the Pt surface. The previously proposed mechanistic models are critically assessed in the light of these new findings.     

吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

High char‐yielding poly[acrylonitrile‐co‐(itaconic acid)‐co‐(methyl acrylate)]: synthesis and properties

Polyacrylonitrile terpolymers of various compositions consisting of acrylonitrile (AN), itaconic acid (IA) and methyl acrylate (MA) were synthesized by solution polymerization in dimethylsulfoxide. Increase in concentration of either IA or MA retarded the overall polymerization rate and the polymer molecular weight. The system consisting of AN + MA and varying IA concentration was more prone to retardation in comparison with the system composed of AN + IA with variable MA concentration. The retardation factors were quantified. Minor quantities of MA boost the reactivity of IA in the terpolymer system. The terpolymer was richer in MA vis‐à‐vis the feed. The thermal characteristics of the terpolymer were examined as a function of its composition. In contrast to the copolymer of AN and IA requiring 1–1.5 mol% IA, the terpolymer required an IA content of approximately 2.5 mol% for optimum thermal stability. The polymer with 90 mol% AN, 2.5 mol% IA and 7.5 mol% MA exhibited reasonably good char‐forming characteristics and thermal stability. The overall crystallinity and crystallite size of the polymers were found to decrease on incorporation of the comonomers. The ‘aromatization index’ of the copolymer increased with the temperature of pyrolysis through re‐organization of the tetrahydropyridine ladder structure. Copyright © 2005 Society of Chemical Industry     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

光化学方法活化CO_2为CO的研究进展

介绍了国内外近年来用光化学方法将CO2活化为CO的研究进展。目前,CO2活化为CO的光化学法主要有气相活化法、均相活化法和非均相活化法,对这些方法的特点及反应机理进行了总结。     

Preparation and Properties of Rare Earth Modified Carbon Black/Natural Rubber Composites

The oxides Eu, Ho, Er and Dy were used to prepare the hydroxides of rare earth modified carbon black. Then natural rubber latex （NRL） was added into the reactor. The system reacted at 85 ℃ with stirring for 1 h to prepare powdered HAF-Ln（OH）3/NR composites. The effects of the kind and content of Ln on the particle size distribution of P [ NR/HAF-Ln （OH）3 ] and mechanical properties of its vulcanizate were studied respectively. It is found that rare earth can help to get the powder of the composite, the product particle with a diameter less than 0.9mm will be get when the composites containing the compound of Ho, Er and Dy with dosage of 1.0, 1.0, O. 5 percent, respectively. The adding of Ln can improve the tensile strength and tear strength of the vulcanizate effectively, what＇s more, Er and Dy can decrease the permanent set of vulcanizate significantly. The SEM studies shows that P[ NR/HAF-Dy （OH）3 ] vulcanizate shows superior mechanical properties that depend primarily on the absence of free carbon black, the fine dispersion of carbon black in the rubber matrix and better polymer-filler interaction.     

MIP-CGP工艺专用催化剂CGP-1的开发与应用

阐述了生产汽油组分满足欧Ⅲ排放标准并多产丙烯的催化裂化工艺（简称MIP-CGP）专用催化剂（简称CGP-1）的研究开发与工业应用结果。CGP-1催化剂的基质具有良好的容炭性能，使活性组元受到良好保护，其优势作用在第二反应区得以充分发挥，具有更高的氢转移活性和强的汽油小分子烯烃裂化活性。中国石化九江分公司和镇海炼化公司的MIP-CGP工业试验标定结果表明，与常规FCC相比，采用CGP-1催化剂的MIP-CGP技术在生产烯烃体积分数小于18％的汽油组分的同时，丙烯产率达到8％以上。此外，汽油诱导期大幅提高，抗爆指数增加；总液体收率有所提高，干气产率下降，焦炭选择性良好。