施加复合电磁搅拌对A357合金微观组织的影响

在半固态加工技术中，电磁搅拌是最早应用于制备非枝晶浆料的方法之一，同时也是半固态触变压铸技术最早获得工业应用的重要技术基础之一。采用自行开发的电磁搅拌器，研究了多种不同电磁搅拌方式在不同工艺条件下，单独施加或复合施加对A357合金微观组织的影响。试验结果表明：单一施加旋转感应电磁搅拌时，浆料径向组织很不均匀；单一施加无芯感应电磁搅拌。当搅拌电流较小时，径向组织也不均匀，增大电流，浆料质量有明显改善；采用（旋转感应＋无芯感应）复合电磁场进行复合电磁搅拌时，可在电流较小时获得满意的浆料质量。     

Development of ultra light magnesium-lithium alloys

Magnesium-lithium alloys are among the lowest density metallic materials. Addition of lithium, with a relative density of 0·53, in magnesium reduces the density of the alloy significantly. Furthermore, addition of nearly 11 wt.% lithium converts hexagonal close packed structure of pure magnesium to a body centered cubic lattice, markedly improving formability of the alloy. The development of these alloys, however, had been hampered due to the high reactivity of lithium and magnesium in the molten state and also, due to poor creep resistance and instability of mechanical properties at room temperature. In an attempt to indigenize these ultra light alloys for possible applications in Indian satellite programme, detailed research work was initiated in DMRL. The difficulties associated with producing sound cast ingots have been overcome by controlling melting and casting parameters of these alloys. Extensive work has been done on structure-property correlation of alloys with varying lithium content and minor alloying additions. Based on these work, advanced magnesium-lithium alloys have been developed with improved tensile properties, room temperature stability and creep resistance. Wrought products (plates/sheets) of magnesium-lithium alloy have been supplied to ISAC, Bangalore and are being used in their INSAT-2 programme. This paper describes the systematic studies carried out in the laboratory to indigenize these ultra light alloys.     

Cu－Zn－Al合金中贝氏体的有序性

本文用Ｘ射线研究了Ｃｕ－２０Ｚｎ－６Ａｌ（ｗｔ％）合金中贝氏体结构的有序性，并与马氏体结构进行了比较，实验表明，从高温Ｂ２母相和低温Ｌ２１母相生成的贝氏体中（１１５）和（２０５）衍射峰或（１２１０）和（２０１０）衍射峰是重叠的，对生成的贝氏体进行一段时间的保温或缓慢冷却处理，其衍射峰的特征并不改变，这与马氏体（１１５）和（２０５）衍射峰或（１２１０）和（２０１０）衍射峰的分离特性不相符合。说明贝氏体结构有序度与马氏体明显不同，它的形成不可能继承母相的有序度。     

机械研磨 Ni_(50)B_(50)合金形成非晶的过程

本文研究了机械研磨 Ni_(50)B_(50)合金非晶的形成过程。唯象地提出用 J-M-A 方程描述此过程,并作了简单的讨论。     

莫来石材料的研究现状及其应用

较详细地介绍了莫来石的性能、生产、研究现状和用途。尤其对多元复合莫来石韧性陶瓷及莫来石超细粉末的制备进行了评述,同时展望了莫来石作为高级陶瓷材料的发展前景。     

Stored energy analysis of Zn—5Al eutectic alloy in superplastic deformation

The stored energy and the energy release during SPD(superplastic deformation)of a Zn-5Al alloy were studied.The alloy after rolling process gains more stored energy,and the as-rolled speciment can obtain maximum elongation and minimum flow stress without hot loding treatment before SPD.Experimental results show that stroed energy release process is along with SPD process and is also an impetus to SPD.The as -rolled Zn-5Al alloy has 48J/mol stored energy which was measured with DSC(differential scanning calorimeter)and conforms well to the calcuated value.The as-rolled Zn-5Al alloy after SPD with an elongation of 2500% releases 112J/mol stored energy,Analysis shows that the strain rate is in direct ratio to the rate of stred energy release.     

机械合金化Zr-Al-Ni-Cu-Ag非晶合金的晶化行为

研究了机械合金化非晶态Zr65Al7.5Ni10Cu7.5Ag10合金的晶化过程，由于存在扩散不均匀区，机械合金化非晶合金在深过冷液相区的退火组织不同于快淬合金，在深过冷液相区退火，析出二十面体准晶相及一些知相：在靠近第一个放热峰的温度退火，近出Zr2Cu相：第二个放热峰对应残余非晶相及准晶相向Zr2Ni,Zr2-Al3的转变。     

铝活塞余热淬火和自然时效的应用研究

图 1所示的活塞试件 ,在开型时间为 5 0s～ 5 5s时 ,其表面温度为 (4 90± 5 )℃ ,可满足淬火要求。自然时效时间为 2 4天时 ,其机械性能可达到国标技术要求。这种新工艺有明显的经济效益。     

非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经预退火后的晶化动力学的DTA研究

研究了非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经400℃，保温10min预退火后的晶化动力学。结果表明；该合金的晶化相为α-Fe固溶体和Sm2Fe17Cx金属间化合物，两相的晶化表观激活能分别为557KJ/mol和514KJ/mol，当晶化体积分数为60%时，α-Fe相的晶化激活能达极大值；Sm2Fe17Cx相晶化激活能则随其晶化体积分数的增加而逐渐减小。     

钼还原过程相变化研究

采用钼酸铵直接氢还原及钼酸铵先焙解然后再分段氢还原两种不同的还原方法进行了钼粉还原。通过Ｘ射线衍射方法分析了两种工艺还原过程中的反应序列及相变化规律，并讨论了不稳定相Ｍｏ４Ｏ１１对于钼粉还原过程的影响。