JX系列高温脱氯剂的开发

通过脱氯剂穿透氯容随实验条件变化规律的研究，讨论高温脱氯剂的脱氯反应模型。基于对脱氯机理的认识，通过对活性组份筛选和制备方法研究，成功研制出以JX-5A脱氯剂为代表的JX系列高温脱氯剂，穿透氯容达到50％以上。     

Effects of perfluoroether concentration and curing protocol on morphology and mechanical properties of toughened TGDDM/MNA resin systems

Previous published work has shown that hydroxyl terminated perfluoroether oligomers can be suitably modified and functionalised to make them miscible with epoxy resins in the uncured state. The reaction conditions can adjusted to induce phase separation either through spinodal decomposition to produce an IPN type morphology, or by nucleation and growth if a dispersed-particle microstructure is required.In the present work we examine the relative toughening enhancement efficiency of the two possible heterophase morphologies. Both systems show a sigmoidal increase in fracture toughness, with increasing concentration of the perfluoroether modifier. However, this takes place at much lower modifier concentrations for the systems with a particulate morphology (about 3.5% w/w) than for IPN systems (about 7.5% w/w). The maximum fracture toughness achievable for the two systems, on the other hand, is very similar and coincides with the concentration at which co-continuous phases are formed.These differences in morphology, however, are not reflected in the variation of modulus and compressive yield strength with increasing concentration of perfluoroether modifier, in so far as both systems exhibit a gradual and small reduction in property with increasing concentration. Furthermore, the dynamic mechanical spectra of the two systems are very different, but the changes resulting from increasing the concentration of toughening agent are relatively small in either case.Nanoindentation tests indicate that it is the local plasticity, brought about by the presence of the softer perfluoroether phase, which is responsible for the enhancement of fracture toughness. This is corroborated by AFM examinations, which reveal local plastic deformations in the regions surrounding the softer particles.     

基于知识情感等级BDI主体的决策行为模型研究

为了将知识、信念、愿望和意图以及害怕、焦虑和自信对决策行为的影响的强烈程度进行形式化,把无穷值的卢卡斯维茨逻辑的真值取值范围从[0,1]扩展到[-1,1]。知识情感等级BDI主体的决策行为通过添加了具体条件的不同背景的不同测度来决定;知识情感等级BDI主体模型清晰地表示了主体的知识状态、心智状态和情感状态的不确定性;此模型可以轻易地向其他类型的主体进行推广。在给出了知识情感等级BDI模型的语言、语义以及此模型的不同背景之间的相互关系之后,对知识情感等级BDI主体的军事决策行为进行了实例分析。此研究旨在为分布式人工智能和军事仿真提供形式支持。     

Effect of randomization on the oxidative stability of corn oil

Randomized corn oil TAG oxidized much faster than natural oil, but after purification with alumina, they oxidized at the same rate. We showed that this effect could not be attributed to a difference, in total tocopherols in the randomized and natural oils. Polar material recovered from the alumina treatment was fractionated by TLC, and a pro-oxidant effect was found in the fractions containing MAG and DAG. However, MAG and DAG, although mild pro-oxidant could not account for the pro-oxidant effect generated by randomization. No other compounds could be detected in the MAG fraction by MS. The pro-oxidant effect of randomized oil disappeared when EDTA or citric acid was added in sufficient amounts. The pro-oxidant effect of randomized corn oil was increased by the incorporation of additional copper or iron at a concentration that did not catalyze oxidation of the purified oil. Treatment of corn oil with ascorbic acid, ascorbyl-6-palmitate, ethyl acetoacetate, ethyl diacetoacetate, and acetylacetone did not reproduce the effect of the unknown pro-oxidant. Although the identity of the pro-oxidant is still unknown, we have confirmed that it is produced during randomization; it does not have pro-oxidant activity alone, but it facilitates the catalytic activity of the transition metal ions.     

选择性螯合滴定法测定电镀液中的锡铜铅

提出了测定电镀液中锡铜铅的一个简易快速螯合滴定法.用EDTA螯合锡(Ⅳ)、铜(Ⅱ)、铅(Ⅱ)和其它金属离子,然后分别用三羟基苯甲酸、巯基丁二酸和氨荒丙酸解蔽.释放出的EDTA,用锌标准溶液反滴定(XO-CPB为混合指示剂).终点变化相当敏锐.研究了测定锡、铜、铅时一般共存离子的干扰.此法已被成功地用于测定锡-铜-铅合金电镀液和镀层锡铜铅合金中的锡、铜和铅.     

化学还原法制备Ag-TiO2光催化抗菌材料的研究

选用平均粒径分别为30nm和8μm的二氧化钛为原料,利用化学还原法制得银质量分数为0. 7% ~5%的Ag-TiO2光催化抗菌材料,采用抑菌圈试验对其抗菌性能进行研究,通过光催化降解亚甲基蓝实验研究了二氧化钛载银前后光催化活性的改变。结果表明,负载1% (质量分数)银的平均粒径为30nm的二氧化钛经250℃热处理后具有良好的抗菌性,其催化活性没有改变。     

Natural fiber composites of high‐temperature thermoplastic polymers: Effects of coupling agents

Our earlier paper (Jana, S.C.; Prieto, A. J Appl Polym Sci 2002, 86, 2159) on the development of natural fiber composites of high‐performance thermoplastic polymers described a new methodology for the manufacturing of composite materials of a high‐temperature thermoplastic polymer, poly(phenylene ether) (PPE) and wood flour, a cellulosic natural filler. A thermosetting epoxy, used as a reactive solvent, reduced the processing temperature of PPE/epoxy blends to well below the decomposition temperature of natural fillers. In addition, the epoxy component, upon polymerization, formed coating layers around the filler particles to provide resistance against moisture diffusion and attacks by acids and alkali. This article describes the results of an investigation on two outstanding issues: (1) the influence of cellulosic wood particles and coupling agents on the speed of epoxy curing and reaction‐induced phase separation and (2) the effects of coupling agents on the morphology of crosslinked epoxy at the surfaces of natural fillers and mechanical properties of the composites. It was found that wood particles expedited epoxy curing in the composites; the extent of epoxy curing, however, was reduced in the presence of coupling agents. Also, the coupling agents promoted complete coverage of wood flour particles by polymerized epoxy, although the mechanical properties deteriorated over systems without coupling agents. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2168–2173, 2002     

一个保护代理人身份的多级代理签名方案

基于RSA签名体制,提出了一个新的可以保护代理人身份的多级代理签名方案。新方案采用影子身份产生中心给每个代理人产生一个影子身份,并用影子身份为消息签名,可确保保护代理人的身份不被泄露,并保证当某个代理人滥用职权时,权威机构可以要求影子身份产生中心根据其影子身份追溯到他的真实身份。同时该方案也满足不可否认性,可区分性,不可伪造性等。     

Fundamental foaming mechanisms governing the volume expansion of extruded polypropylene foams

This article describes the fundamental foaming mechanisms that governed the volume expansion behavior of extruded polypropylene (PP) foams. A careful analysis of extended experimental results indicated that the final volume expansion ratio of the extruded PP foams blown with butane was governed by either the loss of the blowing agent or the crystallization of the polymer matrix. A charge coupling device (CCD) camera was installed at the die exit to carefully monitor the shape of the extruded PP foams. The CCD images were analyzed to illustrate both mechanisms, gas loss and crystallization, during foaming at various temperatures, and the maximum expansion ratio was achieved when the governing mechanism was changed from one to the other. In general, the gas loss mode was dominant at high temperatures and the crystallization mode was dominant at low temperatures. When the gas loss mode was dominant, the volume expansion ratio increased with decreasing temperature because of the reduced amount of gas lost. By contrast, when the crystallization mode was dominant, the expansion ratio increased with increasing temperature because of the delayed solidification of the polymer. The processing window variation with the butane concentration, the change in the temperature ranges for the two governing modes, and the sensitivity of melt temperature variations to the volume expansion ratio are discussed in detail on the basis of the obtained experimental results for both branched and linear PP materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2661–2668, 2004     

生物质功能整理剂的研究进展

传统的功能整理剂都是通过有机合成技术制备得到的,部分会对人体构成潜在的伤害,因此开发生态保健的生物质功能整理剂具有重要的的意义。生物质功能整理剂是从生物体中提取获得的,因此具有绿色安全、生态环保以及可生物降解等众多优势。对生物质功能整理剂在纺织染整行业中的应用进行了综述,并对将来的发展趋势进行了展望。