Sensitizing Mechanism and Adsorption Properties of Dye—Sensitized TiO2 Thin Films

The dye-sensitized TiO2 complex films were prepared by the dye coat onto TiO2 surfaces,and the sensitizing mechanism and adsorption properties of the dye-sensitized TiO2 complex films were inverstigated.The influence of the application conditions of dye adsorbed on TiO2 films on the amount of dye adsorption was discussed.Experimental results show that the concentration,the temperature of dye solutions and the dipping time of TiO2 films in the dye solutions have a significant influence on the amount of dye adsorption.Cell test indicates that the conversion efficiency of light to electricity increases with the amount of dye adsorption.     

Design of pole-assignment controller for systems with algebraic-equation constraint

In this paper we have studied the control of linear systems with algebraic-equation constraint. A pole-assignment controller with two-layer structure for such constrained systems has been presented. The objective of the controller is to assign the desired poles to constrained system and simultaneously force the corresponding closed-loop system to satisfy the constraint. The conditions for the existence of pole-assignment controller are discussed in different cases. The implementation algorithm of pole-assignment controller is also presented. An example is given to illustrate the validity of the method in this paper.     

基于ODMG—93标准的面向对象视图集成机制

模式集成多数据库系统中需要解决的关键问题之一，己存在的大多数面向多数据库系统都采用了面向对象视图机制来建立集成模式。为了满足基于ＣＯＲＢＡ的ＣＩＭＳ信息集成平台呆订成的需要，本文提出了一种基于数据库管理组ＯＤＭＧ的ＯＤＭＧ－９３标准的视图集成机制并通过一个完整的例子说明了这种视图机制在模式集成中的应用。     

湿敏半导体材料电导率计算方法的研究

结合修正了的耗尽层理论和多孔湿敏半导体的特点，本文提出了一个简单的物理模型作为ｎ型湿敏半导体特征的一级近似。描述了多孔湿敏半导体的导电机理，并给出了湿度与宏观电导率的关系。     

Growth of Fe on Si (100) at room temperature and formation of iron silicide

Low-energy electron diffraction (LEED), Auger electron spectroscopy and X-ray photoelectron spectroscopy (XPS) investigations of both the growth of an iron film on silicon (100) at room temperature and the subsequent formation of iron silicide are the subjects of this paper. An in-situ cleaned silicon (100) wafer without carbon or oxygen contamination exhibiting the known 2 × 1 reconstruction in the LEED pattern served as the substrate. Iron was deposited on this reconstructed surface at 300 K. The comparison of theoretical calculations based on three growth mechanisms with XPS data obtained with take-off angles of 0° and 50° clearly demonstrates a layer-by-layer growth of the iron film on silicon (100). At 300 K no formation of iron silicide was observed, although an interaction between iron and silicon could be detected at the interface. The formation of iron silicide was observed at annealing temperatures of 630–730 K. Quantitative XPS analysis yields the presence of FeSi₂, when the thickness is large enough. Neither the iron film on silicon nor the silicide shows any LEED pattern.     

苎麻阳离子改性的研究（三）：改性苎麻的染色机理

采用上染速率，等温吸附模型，Ｚｅｔａ电位、染料与纤维的结合力等方法从理论上研究了改性苎麻的染色机理，苎麻改性后，纤维表面的Ｚｅｔａ电位由原来的－４２ｍＶ提高到－１８ｍＶ，正电性显著增加，提高了阴离子染料对改性苎麻的亲和力，上染率高，节约染料。     

Software for dynamic reconfigurable order picking systems

This paper describes an approach, conceptual framework, and software architecture for dynamic reconfiguration of the order picking system. The research and development project was sponsored by the Material Handling Research Center (MHRC), a National Science Foundation sponsored Cooperative Industry/University Research Center. The storage configuration is assumed to be an in-the-aisle order picking system in which stockkeeping units (SKUs) can occupy variable capacity storage locations and stock-splitting is allowed among zones (clusters). The product mix may include multiple product families with different life cycles, correlated demand within families and commonality of demand across families.     

夏季面漆起泡的预防

面漆漆膜在夏季潮湿天气下成膜后3—5天，漆膜表面易形成米粒状的漆泡，针对漆泡的现象，寻找其形成的机理，根据起泡的机理采取预防面漆起泡的措施。     

压裂泵往复密封性能及机理研究

根据流体动压润滑理论，对压裂泵柱塞密封摩擦副的润滑机理进行了理论分析。在排出和吸入行程，柱塞密封摩擦副均能满足流体动压润滑的条件，即在柱塞与密封界面上能形成并保持一定厚度的油膜润滑密封，从而达到减小摩擦提高寿命的目的；建立了摩擦界面油膜厚度和泄漏量的计算公式。利用有限元法理论，对密封圈的压力沿轴向的分布规律、泄漏量与压力变化关系进行了模拟计算。对往复密封圈沿轴向压力分布、泄漏量随压力变化进行了测试；试验结果表明，建立的计算模型具有较高的计算精度，揭示了压裂泵的密封机理。     

浸入凝胶法聚合物膜形成机理的研究现状

从热力学、传质动力学、相分离机制和固化过程几方面综述了浸入凝胶过程中聚合物膜形成机理的研究现状 .指出浸入凝胶成膜过程是传质交换和由传质交换引发的相分离以及其后的固化过程之间相互竞争的复杂非平衡过程 ,膜结构是上述几个过程竞争的结果