New concept of surface modification to LiCoO2

As the continuance of our series study on LiCoO₂ surface modification, the complicated traditional surface coating method is replaced with simple addition of amorphous YPO₄ and Al₂O₃ in commercial LiCoO₂ or in commercial electrolyte based on our understanding to the improvement mechanism of surface modification. Comprehensive studies by X-ray photoelectron spectroscopy (XPS), gas chromatography and mass spectroscopy (GC–MS), inductively coupled plasma (ICP) and Fourier transformed infrared (FTIR) indicate that the products of spontaneous reaction between the additive and the LiPF₆ based electrolyte are responsible for the performance improvements.     

Evaluation of the reactivity of titanium with mould materials during casting

A methodology for evaluating the reactivity of titanium with mould materials during casting has been developed. Microhardness profiles and analysis of oxygen contamination have provided an index for evaluation of the reactivity of titanium. Microhardness profile delineates two distinct regions, one of which is characterised by a low value of hardness which is invariant with distance. The reaction products are uniformly distributed in the metal in this region. The second is characterised by a sharp decrease in microhardness with distance from the metal-mould interface. It represents a diffusion zone for solutes that dissolve into titanium from the mould. The qualitative profiles for contaminants determined by scanning electron probe microanalyser and secondary ion mass spectroscopy in the as-cast titanium were found to be similar to that of microhardness, implying that microhardness can be considered as an index of the contamination resulting from metal-mould reaction.     

Magnetism in SiC implanted with high doses of Fe and Mn

High concentrations (0.1–5 at.%) of Mn or Fe were introduced into the near-surface region (≤2000 Å) of 6H-SiC substrates by direct implantation at ～300°C. After annealing at temperatures up to 1000°C, the structural properties were examined by transmission electron microscopy (TEM) and selected-area diffraction pattern (SADP) analysis. The magnetic properties were examined by SQUID magnetometry. While the Mn-implanted samples were paramagnetic over the entire dose range investigated, the Fe-implanted material displayed a ferromagnetic contribution present at <175 K for the highest dose conditions. No secondary phases were detected, at least not to the sensitivity of TEM or SADP.     

注入氮离子的SiC涂层阻氢性能研究

利用离子束混合－离子注入（Ar^ ）和磁控溅射相结合的实验技术在HR－1不锈钢基体上制备了注入N^ 的SiC涂层，并用表面分析手段对所制备涂层的表面形貌，剖面形貌、相结构，表面成分，表面元素的化学态进行了分析，结果表明：制备的涂层结构致密，表面平整、膜层成分均匀；涂层与基体之间形成了一明显的过渡层，增强了涂层和基体之间的结合力，用二次离子质谱（SIMS）对充氘涂层的阻氢性能进行了定性分析，结果表明，涂层元素与氢形成稳定的化学键，抑制了氢的扩散和迁移，使得涂层具有一定的阻氢能力。     

超强吸水树脂的吸水性能研究

对自制的超强吸水树脂的吸收性能进行了研究，分别考察了吸水树脂的粒径，溶液的pH值，几种离子如Na^ ,K^ ,Ca^2 ,Mg^2 等的水溶液对吸水树脂吸收性能的影响。实验结果表明，在pH为6－8，树脂粒径为100mesh-120mesh时，树脂的吸水性能最好，各种离子对吸水树脂吸收性能的影响大小顺序为：Na^ ＜K^ ＜Mg^2 ＜Ca^2 。     

CHARACTERIZATION OF Si_(1-x-y)Ge_xC_y FILMS GROWN BY ION IMPLANTATION AND SUBSEQUENT SOLID PHASE EPITAXY

Si1-x-yGexCy ternary alloy films were grown on monocrystalline silicon substrates by C ion implantation and subsequent solid phase epitaxy (SPE). Two-step anneal-ing technique was employed in the SPE. The structure and electrical properties of the alloy films were determined using Fourier transform infrared spectroscopy and van der Pauw Hall measurements, respectively. With the optimization of two-step anneal-ing technique for the implanted Si1-x-yGexCy layers, a certain amount of C atoms occupied substitutional sites and no SiC was formed.     

依靠弯道控导河势流路

在天然河道中，河势演变虽具有一定的随机性，但仍有一定的规律可循，在一个河段内，一般可归纳出2－3条基本流路，为控制河势变化，需要选择出一条基本流路进行河道整治，当连续发生枯水期或洪水期时，部分河段的河势可能出现大的变化，为防止不利河势向下游传播，可修建较长的龙头弯道工程，利用龙头弯道工程分段调整，控导河势，保持河势稳定。     

高炉鼓风机就地扩容改造方案及经济效益

介绍了利用高炉鼓风机基础实施不易地扩容改造的设计工艺方法，该方法不仅降低了设计、施工、安装费用，而且缩短了施工周期，降低了固定资产投资。     

Synthetic resins: XV. Chelation ion exchange properties of 2,4- dinitrophenylhydrazone of resacetophenone-formaldehyde resin

A number of copolymers were synthesised by condensing the 2,4-dinitrophenylhydrazone of resacetophenone with substituted benzoic acids/ phenols and formaldehyde in the presence of sodium hydroxide or hydrochloric acid. The decomposition temperature, solubility and viscosity of the polymers have been determined. The ion-exchange properties have been studied by using a batch equilibrium method. The distribution of a number of metal ions between an aqueous solution and the resin have been measured. A wide range of pH and variable ionic strengths have been investigated.