用双层辉光等离子法在钛表面制备的Ti-Pd合金层性能研究

采用双层辉光等离子冶金技术在纯钛表面制备了Ti—Pd合金层。其深度大约为90μm，Pd含量呈梯度变化，并出现了TiPd3，TiPd2，Ti2Pd3，Ti3Pd5，TiPd，Ti4Pd等6种化合物相和Pd相。合金层在100℃的NaCl饱和溶液＋HCl溶液以及40℃的8．6％H2SO4溶液中的耐缝隙腐蚀性能优于Ti0．2Pd合金；在室温80％H2SO4的溶液中，腐蚀速率仅为0．682mm／a，是Ti0．2Pd合金的18．2％：在室温30％HCl的溶液中，表面Ti—Pd的腐蚀速率仅为0．004mm／a，是Ti0．2Pd合金的12．5％。     

A novel electroless silver depositing method for magnesium alloys

Depositing silver on magnesium alloy by both electroless plating and organic coatings was studied. The organic coating was made by immersing samples in organosilicon heat-resisting varnish. In this method the organic coating acts as interlayer between the substrate and silver film. When the reaction starts, silver deposits directly on the interlayer. X-ray diffraction and SEM analysis were used to determine the composition and morphology of the interlayer and silver film. The potentiodynamic polarization curves for corrosion studies of coated magnesium alloys were performed in a corrosive environment of 3.5% NaCl（mass fraction） at neutral pH （6.9）. The results indicate that compared with the substrate, the corrosion resistance of coated magnesium alloys increases greatly. Moreover, the method proposed in this work is environmentally friendly, non-toxic chemicals were used. In addition, it provides a new concept for the corrosion inhibition of magnesium alloys.     

TWO KINDS OF VARIANT IN SHAPE MEMORY MATERIAL

In shape memory materials,that have been trained to have a two way shape memory effect(TWSM),themartensitic variants are classified into two groups,i.e.,preferentially oriented variants and self-accommodatingvariants.Applied stress may promote or constrain the transition of preferentially oriented variants and so changetransformation temperatures but has no essential effect on self-accommodating variants.According to the pointof view mentioned above,some experimental phenomena during thermocycling of a TWSM device may be ex-plained,such as the absence of synchronization between the plot of resistance change.temperature and the plotof memory strain vs.temperature.     

Microstructure Evolution of Intermetallics Produced by Laser Powder Deposition

NiAl intermetallic alloys are potential high temperaturestructural materials in aeronautical and astronauticalindustries[1].However,the poor ductility andtoughness at room temperature severely restrict theirengineering applications[2,3].It is important todevelop new technology to product intermetallicmaterials for the improvement of the comprehensiveproperties and the workability.Laser powder depositionhas been used to synthesize many new materials.Furthermore,if incorporated with rapid proto…     

Ni-Cr-Fe-Si-B合金涂层及铝青铜基体熔合区组织的研究

采用钨极氩弧焊方法在铝青铜基体上施焊了Ni—Cr-Fe-Si—B合金涂层，并运用金相显微镜、扫描电子显微镜及能谱分析了喷涂层、熔合区及热影响区的组织形貌和成分分布。结果表明，喷焊时，在涂层与基体界面两侧各组元均发生了明显的扩散，Cu、Ni组元间可相互取代，基体融合区组织的基本组成仍为α (α γ2)，但同时也形成了Cu2FeAl7、NiAl3等新相，且融合区组织细小，涂层与基体间为冶金态结合。     

钨钴硬质合金电化学蚀刻加工研究

对YG6硬质合金电化学蚀刻工艺进行了研究,提出了采用光致抗蚀剂作保护膜,在生成一定钝化膜的情况下进行电化学蚀刻的方法.在一定的蚀刻深度范围内,该工艺的可控性好、腐蚀区表面质量较好.     

Formation and thermal stability of amorphous Ni-Mo-P alloys

The experimental researches on the chemical deposition of Ni-Mo-P amorphous alloys were carried out by adding Na2 MoO4 into acidic solutions. The optimum technology conditions were obtained by orthogonal design experiments. The structures and the relationship between compositions and their thermal stability were studied by energy spectrum (EC), scanning electron micrograph and X-ray diffraction spectrum. Compared with Ni-P amorphous alloys, the Ni-Mo-P amorphous alloys have high crystallization temperature and thermal stability, and the hardness reaches its peak when the annealing temperature is 500 ℃. With the increase of the heat treatment temperature, the surface morphology of the alloys changes.     

低碳低合金铸钢力学性能的研究

利用Olympus光学显微镜、扫描电镜(SEM)及能谱分析(EDAX)探讨了等温淬火工艺对低碳低合金CrMnSi铸钢力学性能的影响,并通过XRD定量分析了相的组成.结果表明,合适的等温淬火工艺,可获得一定数量的贝氏体和残余奥氏体(约6%)的复合组织,冲击断口形貌由解理刻面变为韧窝状,铸造成形无缺口试样(10 mm×10 mm×55 mm)的冲击韧度由ακ≤30 J/cm2增加至ακ≥170 J/cm2,硬度HRC≥40,具有较高硬度和冲击韧度的配合.     

Influence of electroplating conditions on magnetic properties of Fe-36wt.% Ni alloy film

A Fe-Ni soft magnetic film was prepared in sulphate solution by electroplating. The influences of the molar ratio of n [Fe2+ ]/ n [Ni2+ ], current density, bath temperature, pH and L-ascorbic acid concentration on magnetic properties of Fe-Ni alloy film were investigated. The results show that the saturated flux density(BS) of the film increases initially and decreases after it reaches the specific value with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density, bath temperature and pH. However, the relationship between L-ascorbic acid concentration and B S keeps linear. It is observed that the coercive force( Hc) is enhanced with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density and pH. By comparison, when the bath temperature increases, Hc always decreases. With the increase of L-ascorbic acid concentration, the coercive force increases initially and then decreases.     

Synthesis mechanism of titanium carbide nano-fiber during self-propagating high temperature synthesis

Titanium carbide nano-fiber was synthesized by self-propagating high temperature synthesis (SHS) method. The final products after the SHS reaction were titanium carbide containing excess carbon and metallic titanium, which were removed by additional leaching process. TEM observation revealed that the average diameter is about 20 nm. Neutron diffraction analysis was carried out to study non-stoichiometric number of the titanium carbide. The non-stoichiometric numbers of the titanium carbide were 0.89–0.94. The Rietveld refinement of each patterns converged to good agreement (÷2=0.49–1.34). The formation mechanism of the carbide is related to a liquid-solid reaction including the preferential diffusion process of carbon atom into liquid titanium. This article is based on a presentation made in the 2002 Korea-US symposium on the “Phase Transformations of Nano-Materials,” organized as a special program of the 2002 Annual Meeting of the Korean Institute of Metals and Materials, held at Yonsei University, Seoul, Korea on October 25–26, 2002.