抽油机球铁齿轮的化学成分及生产工艺

为提高抽油机减速器齿轮铸件的机械性能，提出以Sn代替Mo作为合金元素，并通过试验确定了合理的Si、Cu、Sn的加入量。指出Si加入量应控制在1．9％－2．1％范围内，同时加入0．36％～0．9％的Cu和0．025％～0．07％的Sn，可保证球铁的强度和延伸率都满足QT700－2的要求。鉴于试件与实际铸件的表面硬度有一定的差值，为提高铸件表面硬度，进行了余热正火试验，并给出了铸件在铸型内的时间－冷却温度曲线。最后根据球铁化学成分的选择结果，进行了齿轮生产试验。     

定向凝固空心叶片制壳工艺的改进

分析了在先进发动机定向凝固空心叶片熔模精密铸造生产中出现两种缺陷的性质和产生原因，从壳型制造工艺方面提出了改进措施，提高了叶片合格率。     

Probing acid sites in MAPO-36 by solid state NMR

An ordering of magnesium is observed in the as-synthesized MAPO-36 molecular sieve. Upon calcination, part of the magnesium is removed from the sample and part occupies extraframework positions thus rendering a random distribution of magnesium in the lattice. The shoulder observed in the³¹P spectrum of the calcined sample is assigned to P(3Al, 1Mg) sites in conflict with the earlier assignment to P-OH groups. The bridging hydroxyl groups located at these sites are detected in the¹H MAS spectrum at 3.6 ppm. Further, MAPO-36 catalyzed acetone conversion to mesityloxide that cracked at elevated temperature to yield acetic acid and aliphatics.     

大型离心复合球墨铸铁轧辊的生产

简述了我公司为舞阳铜厂试制４２００ｍｍ厚板轧机离心复合球墨铸铁轧辊的性能要求、内外层双重金属铸造工艺参数的选择及整个铸造生产工艺过程。     

New Ferro Powder for Selective Laser Sintering of Dense Parts

The paper describes a new powder composition specially developed for selective laser sintering (SLS). The aim is to obtain a ferro powder that can be sintered without need for a (sacrificial) polymer binder and that results in quasi dense parts that do not need any post-processing like furnace sintering, infiltration or HIP. The powder is a mixture of different types of particles (Fe, Cu, Ni and Fe₃P). The composition and mixture ratio are justified by using phase diagrams. The powder has been tested using an own developed Nd: YAG SLS machine. The influence of process parameters (laser power, scan velocity, scan spacing and scan strategy) and the microstructural characteristics have been investigated. Attention is devoted to the binding mechanism (liquid phase sintering, through melting) and to the quality of resulting parts (density, balling effect,…).     

Colour extension properties of individual pigments and effects on shades of foundations in cake form

The mechanism of colour change during the pigment dispersion process and during powder application to the skin surface was studied by examining the colour extension properties of Yellow. Red , and Black iron oxides in white powder bases. A new measure for the evaluation of the degree of colour extension was devised. This measure corresponded well with human visual sensation, and was found to be useful for comparing the rates of colour extension of pigments. The rate of colour extension of pigments was found to vary in the order: Yellow acicular Red granular Red Black. This result explains colour darkening and the change towards reddish tones during the pigment dispersion process, because Yellow extends fully in the early stage of the process but Red , especially in granular form, and Black continue to extend even in the later stage. Acicular Red iron oxide is more favourably employed than the granular form to attain sufficient colour extension of foundations with lower energy expenditure, and to decrease the discrepancy between the cake colour and the colour of applied powder.
Le développement des oxydes de fer et effet sur les nuances des fonds de teint compacts     

高炉煤气干法除尘技术发展现状及宝钢应用前景

在对高炉煤气干法除尘技术应用现状进行综合分析的基础上结合宝钢实际，提出宝钢应用此技术的相关建议。     

APPLICATION OF SITE-SPECIFIC NATURAL ISOTOPE FRACTIONATION (SNIF-NMR) OF HYDROGEN TO THE CHARACTERIZATION OF EUROPEAN BEERS

More than one hundred samples of European beers have been investigated by the new SNIF-NMR method which is based on 2H NMR at the natural abundance level and enables site-specific natural isotope fractionation factors in ethanol to be determined. The relative (R) and absolute (D/H)_i, parameters are shown to be characteristic of the country where the beers are brewed and the observed variations are explained in terms of cereal composition, water resource, and manufacturing processing (fermentation, yeast, temperature cycle). These new parameters find analytical and mechanistic applications in the identification of a beer and in the investigation of a fermentation process.     

SiC粒子增强铸造Al基复合材料的研制

本文用真空烘烤封罐法对 SiC 粒子进行预处理,在固液两相区内搅拌添加,制造了铸造 Al 基复合材料。测试表明,该复合材料具有铸造性能好,力学性能高的优点,适用于采用压铸、石膏型精密铸造、金属型铸造等工艺方法成型的活塞、连杆等要求苛刻的零件。     

济钢第一炼钢厂降低钢铁料消耗实践

济钢第一炼钢厂通过优化入炉原料结构,改进冶炼工艺,实施少渣炼钢,有效减少了转炉吹损,降低了钢铁料消耗成本,2002年增加炼钢综合经济效益3100多万元。