Effect of oxygen deficiency (δ) on transition temperature of yttrium cuprate superconductors

The nature of pairing mechanism as well as transition temperature of yttrium cuprates is discussed using the strong coupling theory. An interaction potential has been developed for the layered structure with two conducting CuO₂(a–b) layers in a unit cell. The interaction potential properly takes care of electron-electron, electron-phonon and electron-plasmon interactions. Furthermore, the electron-phonon coupling parameter (λ), the modified Coulomb repulsive parameter (μ*) and the 2D acoustic phonon (plasmon) energy as a function of oxygen deficiency is worked out. Finally, the superconducting transition temperature (T _c) is then evaluated by using these coupling parameters and obtainedT _c = 95(92)K for Y(Yb)Ba₂Cu₃O_7−δ superconductors withδ = 0·0. The model parameters estimated from the layered structure approach are consistent with the strong coupling theory. The result deduced on the variation ofT _c withδ are in fair agreement with the earlier reported data on yttrium cuprates. The analysis of the above results are discussed.     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

薄板坯连铸生产SS400钢工艺技术研究

对唐钢薄板坯连铸机生产的SS400钢的生产工艺进行了分析,认为薄板坯连铸机生产的SS400钢,在采取了精炼站在线定氧,将钢水全氧控制在25×10~(-6)左右,同时连铸采取保护浇注和轻压下等技术后,能够确保薄板坯连铸SS400钢的顺利浇注,轧制的板带材表面质量良好,机械性能符合要求。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

PVDF中空纤维滤膜的形态结构

用Ｌ－Ｓ相转换法制备了聚偏氟乙烯（ＰＶＤＦ）中空纤维不对称滤膜。铸膜液由聚合物、溶剂和添加剂组成。用电子显微镜（ＳＥＭ）考察了聚合物浓度、添加剂用量及种类对膜形态结构的影响。实验结果表明，聚合物浓度对膜形态结构有显著影响，当铸膜液中聚合物浓度较低时，无论用什么种类添加剂，都能形成大、且多的孔，但孔的形状随添加剂不同而异。当恒定聚合物浓度时，添加剂的用量对膜形态结构有很大的影响，但孔的大小及多少与添加剂含量的多少不成正比。     

稀土变质剂对铸造铝合金性能的影响

采用正变试验法，探讨了稀土变质剂对铸造结合金ZL102性能提高的可行性．试验选用了不同的稀土添加量，考察了不同的变质时间及热处理制度对ZL102的强度、硬度、流动性以及重熔性等性能的综合影响规律．试验表明，稀土是铸造铝合金的优良变质剂，并且添加单一稀土的变质效果优于混合稀土．     

Li2O在保护渣中的作用

采用在不同玻璃性的两种基渣中加入Ｌｉ２Ｏ为研究Ｌｉ２Ｏ对保护渣粘度，熔化温度及玻璃性能的影响，并对Ｌｉ２Ｏ改善保护渣玻璃性的机理进行了探讨，提出了寻找高速连铸保护渣中Ｌｉ２Ｏ的代用物的一种方法。     

用过滤工艺全面提高铸锭质量

探讨了过滤器孔径对6063铝合金铸锭组织和性能的影响规律。在此基础上指出,在过滤工艺恰当时,不仅可以减少铸锭中的夹杂物,而且可以有效地防止裂纹、羽毛晶等连续铸锭中的常见缺陷。     

双辊薄带钢连铸在线自动检测系统

介绍了双辊薄带钢连铸工艺,设计了双辊连铸机的计算机在线自动检测系统,通过采取正确的抗干扰措施提高了检测的精度,系统在双辊薄带钢连铸试验中应用效果良好.