真空铸造高强度C/Mg复合材料

本文介绍用真空铸造法制造抗拉强度超过1000MPa的高强度C/Mg复合材料。将T300纤维经C-Si-O梯度涂层处理后单向排布于型腔内,在真空下注入ZM-5合金液,凝固后即得C/Mg复合材料零件或试样。试样的抗拉强度在纤维体积分数为0.35时达1050MPa。本文讨论C-Si-O梯度涂层对获得高强度复合材料的作用。     

Effect of oxygen deficiency (δ) on transition temperature of yttrium cuprate superconductors

The nature of pairing mechanism as well as transition temperature of yttrium cuprates is discussed using the strong coupling theory. An interaction potential has been developed for the layered structure with two conducting CuO₂(a–b) layers in a unit cell. The interaction potential properly takes care of electron-electron, electron-phonon and electron-plasmon interactions. Furthermore, the electron-phonon coupling parameter (λ), the modified Coulomb repulsive parameter (μ*) and the 2D acoustic phonon (plasmon) energy as a function of oxygen deficiency is worked out. Finally, the superconducting transition temperature (T _c) is then evaluated by using these coupling parameters and obtainedT _c = 95(92)K for Y(Yb)Ba₂Cu₃O_7−δ superconductors withδ = 0·0. The model parameters estimated from the layered structure approach are consistent with the strong coupling theory. The result deduced on the variation ofT _c withδ are in fair agreement with the earlier reported data on yttrium cuprates. The analysis of the above results are discussed.     

放置过滤器浇注系统的设计

综述了常用的网型、芯型、泡沫陶瓷过滤器的研究和应用情况。指出应根据过滤器类型，确定其在浇注系统中的安放位置并相应改变该处的结构和截面积，以便在使用过滤器净化金属的同时，保证充型速度不变。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

新世纪我国压铸业与国际接轨的思考

针对中国压铸行业的现状和存在的问题 ,以及当前的机遇和面临的挑战 ,论述了中国压铸工业进入 2 1世纪所面临的新形势及应采取的对策     

连铸机油缸成套密封件国产化

本文论述了冶金行业中连铸机油缸密封件国产化的一些技术参数，同时也介绍了洪格尔型组合密封及夹布V型圈组合密封的使用特点。     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

Investigation of Centreline Segregation and Centreline Porosity in CC ‐ Slabs

Improvements of solidification processing in conventional or near net shape casting depend on sophisticated methods of macroscopic examination of central unsoundness and inhomogeneity of the cast material. As long as remarkable deviations referring to the quality features exist between the slab centre and the bulk material such methods should be looked after. Two semi‐macroscopic methods of segregation analysis are discussed in this paper: firstly, the potential of the emission spectral analysis combined with sectioning of a sample and secondly, the computer aided micro‐probe analysis. Both methods are restricted to small local areas. The proneness of elements and steel grades with respect to micro‐ and macrosegregation as well as distribution‐ and segregation coefficients are determined. The effect of a diffusion anneal on homogenisation of segregation is studied. Last not least the precipitation of sulphides, phosphides or carbonitrides is estimated. Ultrasonic detection of the central unsoundness of conventional slabs or thin slabs is a new approach towards a quantitative macroscopic examination. The sample size is 400 mm x 300 mm x 30 mm. To achieve a low ultrasonic noise using a 5 MHz‐transducer the samples are heat treated for grain refinement. “Dog bone porosity”, macroscopic topographical misfit between the upper and lower solidifying shells, periodical corner cracks or systematic transverse centre cracks are detected. Obviously, segregations do not reflect the ultrasonic beam. However, it can be presumed that an interrelation exists between porosity and segregation, although these might be locally apart from each other. This new ultrasonic test of the central unsoundness of continuous cast (c.c.) slabs gives valuable arguments to machine builders and maintenance people to decide on the right concepts for strand guidance, support rollers and secondary cooling. Soft reduction can be optimized and variations in casting speed counteracted by dynamic means. R&D service of this kind can help steelmakers when decisions are impending to build new casting machines or revamp old ones.     

现代电弧炉流程钢液氮控制的试验研究

通过生产试验研究了电弧炉冶炼过程、LF精炼过程及连铸过程钢液氮的控制。研究表明，电弧炉冶炼过程主要是电弧区增氮，LF过程及连铸过程钢液增氮主要是钢液与大气接触，LF供电制度也对钢液吸氮有影响。